收藏 分销(赏)

WD西部数据并口IDE硬盘十针.doc

上传人:仙人****88 文档编号:9464767 上传时间:2025-03-27 格式:DOC 页数:2 大小:52KB
下载 相关 举报
WD西部数据并口IDE硬盘十针.doc_第1页
第1页 / 共2页
WD西部数据并口IDE硬盘十针.doc_第2页
第2页 / 共2页
本文档共2页,全文阅读请下载到手机保存,查看更方便
资源描述
WD西部数据并口IDE硬盘十针(10针)跳线设置方法 WD西部数据并口IDE硬盘十针(10针)跳线设置方法。(1)Cable Select(电缆选择) 当将一个跳线帽插在“1-2”针上时,此时硬盘便成了“Cable”,这也是硬盘出厂时的默认设置。 如今我们使用的硬盘一般都支持ATA66/100,而用来连接这类硬盘的数据线也由原来的40芯变成了80芯,其实这80芯的数据线不仅仅增强了抗干扰能力,它还有另外一个功能——当硬盘的跳线设置成“Cable Select”时,硬盘的主从关系将由其连接到数据线上的位置而决定。此类数据线用来连接主板的那端叫作“System”,中间的那端叫“Drive1”,另外一端则叫“Drive 0”。 当硬盘的跳线设置成“Cable Select”后,它挂在“Drive 0”上是“Master”(主盘),挂在Drive1上则是“Slave”(从盘)。由于“Cable Select”是根据安装位置来确定主从关系的,所以硬盘不管挂在哪个部位都不需要更改其跳线,非常方便。不过享受“Cable Select”所带来的方便时要注意:所有的IDE设备都得设置成“Cable Select”,另外当硬盘与光驱挂在同一根数据线上时,“Cable Select”可能会失效——光驱不支持“Cable Select”!另外“Cable Select”还需要数据线的支持,如果使用的是劣质数据线,往往也会出现错误,所以对于初学者来说,还是老老实实将硬盘设置成“Master”或“Slave”吧。至于IBM硬盘的“Cable Select”设置则非常简单。 (2)Single(单独硬盘模式) 当将一个跳线帽插在“4-6”针上时,此时硬盘便成了“Single”。此模式适用于一根IDE数据线上只挂一块硬盘。 (3)Master(主盘) 当将一个跳线帽插在“5-6”针上时,此时硬盘便成了“Master”。此模式适用于一根IDE数据线上挂两块硬盘,“Master”设置为系统引导的硬盘。 (4)Slave(从盘) 当将一个跳线帽插在“3-4”针上时,此时硬盘便成了“Slave”。 此模式适用于一根IDE数据线上挂两块硬盘,“Slave”设置为非系统引导的硬盘。 *********************************************************** Set the Jumpers Jumper settings are used to determine the order in which IDE devices (i.e. hard drives, CD-ROM drive, etc.), attached to a single cable, are detected by the system. Western Digital EIDE hard drives have a 10-pin jumper block located next to the 40-pin IDE connector on the hard drive. After you have determined the appropriate drive configuration, you must jumper the drive(s) accordingly. Identify the procedure that corresponds to your configuration. Install the Hard Drive Connect the IDE Interface Cable to the hard drive(s): If installing the hard drive as the only drive on the cable: Connect the black connector of the IDE interface cable to the drive. If installing two drives on the same IDE interface cable: Jumper the bootable drive as Master and the other drive as Slave; then connect the Master drive to the black connector of the IDE interface cable and the Slave drive to the gray connector. Connect the IDE Interface Cable to the Motherboard: Attach the blue end of the IDE interface cable to the 40-pin connector on the motherboard. Match pin 1 on the IDE interface cable to the connector on the motherboard.
展开阅读全文

开通  VIP会员、SVIP会员  优惠大
下载10份以上建议开通VIP会员
下载20份以上建议开通SVIP会员


开通VIP      成为共赢上传
相似文档                                   自信AI助手自信AI助手

当前位置:首页 > 教育专区 > 小学其他

移动网页_全站_页脚广告1

关于我们      便捷服务       自信AI       AI导航        抽奖活动

©2010-2025 宁波自信网络信息技术有限公司  版权所有

客服电话:4009-655-100  投诉/维权电话:18658249818

gongan.png浙公网安备33021202000488号   

icp.png浙ICP备2021020529号-1  |  浙B2-20240490  

关注我们 :gzh.png    weibo.png    LOFTER.png 

客服