DFM报告模板-经典.ppt

,Automotive,Medical,Telco,Consumer/IT,Customer/,客户,:,Project/,项目,:,Product Name:,产品名称编号,:,Prepared By/,制作,:,Date/,日期,:,Approved By/,审核,:,DFM REPORT,Part&Tool info,产品,/,模具基本信息,Revision info/,版本信息,2D Drawing Rev/2D,图纸版本,-,Tool Spec.,Rev/,模具规格版本,-,Mold flow analysis Rev/,模流分析版本,-,Part Info/,产品信息,Plastic Material/,塑料材料,-,Shrinkage/,缩水率,-,General Thickness/,产品平均厚度,-,Surface Texture -,模具零件表面要求,-,Others/,其它特殊要求,-,Mold Info/,模具信息,Type of Moldbase -,Slider/,滑块,-,Lifter/,斜顶,-,Cavities/,模穴数,-,Part View/,配有外形尺寸的产品图,Pls confirm/,请确认,:YES _ NO_,Mould Layout,Pls confirm/,请确认,:YES _ NO_,Part Line/,分模线,The red line is the main Parting line./,红色线为主要分型线。,Pls confirm/,请确认,:YES _ NO_,使用,UG,萃取线来定义分模线,显示主分模线,显示所有窗口分模线,显示滑块和斜顶的分模线,指出需要改变分模线走向的插破角,Slider,lifter&Insert/,滑块,斜顶和镶件,在产品上定义出滑块，斜顶的排布，确定其尺寸是可以在模具设计中实现的；,明确指出产品设计中对滑块，斜顶运动造成障碍的不良设计，并提出相应的改良建议；,如有必要，定义出公母模中需要设计镶件的区域。,Material for Main Parts of Tool/,模具主要零件材料,给出模具主要零件的材料,型腔材料；,型芯材料；,滑块材料；,斜顶材料；,镶件材料。,Gate/,浇口,Pls confirm/,请确认,:YES _ NO_,提供浇口数量和类型，如有必要，需配以模流分析的结果说明,Draft Angle/,拔模角,Pls confirm/,请确认,:YES _ NO_,提供产品的前后侧拔模检查显示图，建议未建拔模面的拔模角。,Thickness/,厚度分析,Pls confirm/,请确认,:YES _ NO_,Geometry issue1/,其它技术问题点,请确认,:YES _ NO_,Uniform wall thickness,缩水,融接线,薄胶,薄铁,Part sticking,Cooling,Flashing potential,Core out requirements,Poke yoke for buttons,1,st,and 2,nd,shot gating(2K Mold),2shot wash-off issues,2shot shut off areas,Shut off angles,Product holding areas,Geometry issue2/,其它技术问题点,请确认,:YES _ NO_,Uniform wall thickness,缩水,融接线,薄胶,薄铁,Part sticking,Cooling,Flashing potential,Core out requirements,Poke yoke for buttons,1,st,and 2,nd,shot gating(2K Mold),2shot wash-off issues,2shot shut off areas,Shut off angles,Product holding areas,Eject Pin Layout/,顶针及位置,Pls confirm/,请确认,:YES _ NO_,Suggest the ejector type and location on the part.,Engraving Details/,刻字要求,Pls confirm/,请确认,:YES _ NO_,Request customer to identify engraving locations for,请选择刻字的内容和要求,Part Numer/,产品编号,-,Recycle symbol/,循环利用标志,-,Date Code/,日期码,-,Product Rev.No./,产品版本号,-,Other customer specific details/,其它的刻字要求,-,Thanks,Thanks,