激光对中仪轴系直线度.pptx

Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB1直线10.110.1平直测量平直测量10.2Activity:两点为参考的直线两点为参考的直线10.3Activity:以旋转轴线为参考的直线以旋转轴线为参考的直线Section 10Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB210.1平直测量检查设备基础检查设备基础 轴轴 设备导轨设备导轨在轴调整中的应用在轴调整中的应用lFixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB3测量类型旋转轴线为基准两点为基准Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB4平直检测或需调整的平直测量平直检测平直检测激光束粗调整(roughly bucked in)平直和调整平直和调整激光束必需被 bucked in 为零Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB5操作过程1.放置 TD单元 2.定义测点和距离Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB6操作过程3.瞄准激光 在近距触电置零 在远距处调整角度Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB7操作过程3.瞄准激光 -”Buck-in”Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB8操作过程3.瞄准激光 -example of”Buck-in”Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB9操作过程4.重复测试放置 TD-M在距TD-S最远的测点Register 5 measurements in the TD-M/TD-S programFixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB10操作过程5.读数Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB11操作过程6.结果的显示Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB12Straightness checkFixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB13以旋转轴线为基准的直线以旋转轴线为基准的直线放置TD单元Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB14以旋转轴线为基准的直线以旋转轴线为基准的直线确定TD-S 的中心1.置零置零2.旋转旋转3.1/24.滑动滑动 TD-S至零至零12.006.00Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB15以旋转轴线为基准的直线以旋转轴线为基准的直线调整激光的角度ConingFixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB16以旋转轴线为基准的直线以旋转轴线为基准的直线调整激光的角度1.Coning直至激光位于探直至激光位于探测器内测器内2.置零然后旋转置零然后旋转3.取半值然后调整至零取半值然后调整至零用用TD-S上的调整螺栓上的调整螺栓.Re-check the centeringFixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB17以旋转轴线为基准的直线以旋转轴线为基准的直线读数Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB1810.2Activity两点为基准的平直1.Perform a straightness measurement(check)by bucking in roughly in two reference points.Register 8 measuring points,Store the measurement and make a printout.Change reference by touching another reference point on the screen and make a printout.2.Perform the same straightness measurement this time by bucking in exactly and if possible make adjustments.Fixturlaser Shaft50Fixturlaser Shaft100Fixturlaser Shaft200Shaft alignment withFixturlaser Shaft systems1999 Fixturlaser AB1910.3Activity：以旋转轴线为基准的直线以旋转轴线为基准的直线Perform a measurement by using the rotational center as reference.8 measurement points Store and make a print out