模具名词中英文对照.doc_咨信网zixin.com.cn

资源描述

模具名词***中英对照**** 为大家提供点模具方面的中英对照希望对你们有帮助噢 top view ----俯视图 front view ----前视图 side view ----侧视图 plane view ----平面图 contour ------外型铣削 pocket ------挖槽 flow line ----罩一曲面 multisurf ------多重曲面 filter -----过滤 ellipse -----椭圆 polar -------极坐标 arc endpoints-----两点画弧 polygon -------多边形 isometric -------等角视图 zig zag -------双向 one way -------单向 spline -------圆滑曲线 blend -------顺接 guide pin --------导针;边针;直边 support pin ---------拉杆;水口边 support pin collar --------拉杆定位;水口边定位介子 tapped hold for eyebolt -------吊模螺孔 thermal expansion coefficient -------热膨胀系数 welding rod -------熔接棒 cavity plate; A bolster plate(holder material) --------母模板 (A板), 前模板 stripper plate ---------活动板,推料板 core plate --------公模板 (B板),后模板 spacer block -----------间隔板 ejector retainer plate -----------上顶针板 ejector plate -----------下顶针板 pin point gate system -----------小水口系统 side gate system -----------大水口系统 infrared-transmitter ------------红外线发射器 infrared-receiver ------------红外线接受器 synthetic resin ------------合成权脂 air blow gun(with nozzles&hose) -----------------气枪 spiral hose -----------------螺旋形的;盘旋的 guide strip ---------------行位导轨 ejector rod --------------斜坊 set screw ---------固定螺丝 countersunk screw ---------沉头螺丝 hex screws --------胚头螺丝 shoulder screw -----------------带肩螺丝 residual stress -----------------残余应力 tensile ---------------------------------张力 electricity erode -----------------电蚀刻 ohm meter -------------------电阻表 tubular dowel -----------------管钉,销钉 abrasive stone -----------------研磨石材 SPI Mold Finish Comparison Kit ------------------SPI模具抛光比照工具 rolled ------------------热轧 forged ------------------热锻 extrude ------------------挤压 cold drawn -------------------冷拉 corrosive plastics -----------------防腐塑料 tough -----------------硬度 anneal -----------------n.退火 service life --------------------注塑寿命 high viscosity -----------------粘度较高的 extension plug ------------------延伸尾塞 angle plug -------------------斜角尾塞 thermocouple connector -----------------热电偶连结头 hydraulic system ----------------------(注塑机的)油压系统 temperature control zone -------------------温控区 barrel heating capacity --------------------料筒加热能力 screw torque -----------------------螺杆力矩 screw speed -----------------------螺杆速度 screw stroke -------------------------螺杆行程 nozzle contact force ---------------------热嘴接触力 screw L/D ratio ---------------螺杆长度/直径比例 theoretical shot volume --------------理论的注射容量 clamp force --------------------合模力 lock force ---------------------------锁模力 internal heated ------------------------内部加热 external heated ------------------------外部加热 heating rod -------------------------加热棒 air-gap insulation ------------------------空气隔绝层 spare part(accesory) --------------------------备用件 insulating ring -----------------------绝缘圈 sealing washer -------------------------垃圾钉 adaptor ---------------------适配器 hole gauge ----------------------孔深量测仪 high-temperature grease -------------高温油脂 thermal conductivity paste --------------导热膏 data cable --------------数据线 compression mold base ---------------压缩模胚 countersunk -----------------埋头孔锥孔,沉孔 mill --------------压榨机;磨坊;碾磨; drill ---------------钻头;钻床钻孔;钻通 grind -----------------磨擦;磨碎;磨光 turn ---------------转动;旋转;翻转 adapter plate --------------------适配模板 leader pin; shoulder leader pin ----------------导针;带肩导针( 实心) angle pin(horn pin) -------------------斜针;斜边 straight bushing ----------直导套(空心) shoulder bushing ----------带肩导套 sprue puller pin ----------唧咀扣针 sprue spreader -----------浇口分流锥 runner spreader -----------流道分流锥 tapered interlocks(round & rectangular) ------------啤把锁 bronze plated bushing -------------------镀铜导套 guided ejection bushing ----------------------------导向导套 toggle-lock early ejector return -------------------------切换式早期回撞装置 accelerated knock-out ---------------------加速顶棍 accelerated ejector ---------------------加速顶针 collapsible core ---------------------可折迭式的型芯 slide retainer ----------------------行位固定装置 jiffy latch-lock assemblies ---------------------快速拉杆锁定装置 tapped hole ------------------螺丝孔 no resettable shot counter --------------------非复位注射计数器 profiled ejector pin --------------------底面在有倾斜截面的顶针 copper -------红铜 brass ------- 黄铜 bronze --------青铜 BeCu --------铍铜 counterbore ---------------拔头,介子托 fan gate -----------------扇形入口 fillet ----------------圆形入口 pin point gate -------------细水口 hose clip --------------入喉箍 jiggle ----------------斜顶 British Standard Whitworth thread BSW --------------英制螺丝(粗牙) British Standard Fine Thread BSF -------------------英制螺丝(幼牙) National Pipe Thread -----------------------美制螺牙 pressure plug ----------------喉塞 pressure spring -----------------压力弹簧 vent ------------------ 疏气孔 alignment strip --------------------斜锁 ball catch ---------------------弹弓波子 bridge piece ------------------水口铁 Jiffy-matic connector ---------------------快速连接喉 All ejector blades must have key to avoid rotating. 扁顶要管定,以防旋转. ejector bearing length 弹弓压缩长度 reinforcement rib 加强筋 steel pad 方铁 latch 拉杆 sprue puller insert 扣针导套 stage ejector=knock out 顶棍 ejector retainer plate 上顶针板 ejector base plate 下顶针板 stripper plate 活动板 runner stripper plate 脱料板 P/L flash 分形面披锋 scrape 拖花 burn 烧黑 safety strap 码板 side gate system 大水口系统 three plate type system 简化型细水口系统 pin point gate system 细水口系统 guide pin/guide bush 直边/托司 top clamp plate 工字板 stripper plate 推板 spacer block 方铁 bottom clamp plate 底板 shoulder guide pin 带肩导针 shoulder guide bush 托司 straight guide bush 直司/直导套 guide pin 直边 screw thread 螺纹 air pump 空气泵 alloy 合金 alloy steel 合金钢定模座块 fixed clamp plate;top clamping plate;top plate 动模座块 moving clamp plate;bottom clamping plate;bottom plate 上模座块 upper clamping plate 下模座块 lower clamping plate 凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate 突模固定板 punch-retainer plate 模套 chase;bolster;frame 支承板 backing plate;support plate 垫块 spacer;parallel 支架 ejector housing,mould base leg 斜销 angle pin,finger cam 滑块 slide,cam slide 侧芯型滑块 side core slide 滑块导板 side guide strip 楔紧块,撑鸡 heel block,wedge bock 斜槽导板 finger guide plate 弯销 dog-leg cam 斜滑块 angle-lift splits 导向零件导柱 guide pillar;guide pin;leader pin 推板导柱 ejector guide pillar;ejector guide pin 带头导套 guide bush;guide bushing 推板导套 ejector guide bush;ejector bushing 定位和限位零件锥形定位件 mould bases locting elements 复位杆 ejector plate return pin,push-back pin 限位块 stop block; stop pad 定距拉杆 length bolt; puller bolt 定距拉板 puller plate; limit plate 推出零件推流道板 runner stripper plate 分流道拉料杆 runner puller; runner lock pin 拉流杆;扣针 sprue puller 钩形拉料杆 sprue puller, Z-shaped 球头拉料杆 sprue puller,ball-headed 圆锥头拉料杆 sprue puller,conical headed 连接推杆 ejector tie rod 推板 ejector plate;ejection plate 推杆固定板 ejector retainer plate 推件环(盘) stripper ring(disk) 推件板 stripper plate 推块 ejector pad 推管(司筒,导筒) ejector sleeve 推杆 ejector pin 圆柱头推杆 ejector pin with cylindrical head 带肩推杆 shouldered ejector pin 扁推杆 flat ejector pin 塑料成型模具的主要设计要素脱模距 stripper distance 脱模斜度 draft 投影面积 projected area 最大开距 maximum daylight;open daylight 闭合高度 mould-shut height 抽芯距 core-pulling distance 抽芯力 core-pulling force 脱模力 ejector force 开模力 mould opening force 模内压力 internal mould pressure;cavity pressure 成型压力 moulding pressure 背压环 back-up ring 1 bar = 14.5psi 高压接头 bite type fitting 液压马达 hydraulic motor 冷却水流量计 waterflow regulator 打磨器材 abrasive material 打磨砂轮 grinding wheels 切割砂轮 cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools 高压力软管 high pressure hose 风管,水软管 air .water hose 高压油表 pressure gauge 压力油喉 hydraulic hoses 光塑检测 photoelastic testing 吹塑模 plastic blow mould 注塑模 plastic injection mould 冲扎复合模 blank & form compound die 精密冲模 precision blanking die 熔料流动率 MFR=melt flow rate 熔料流动指数 MET=melt flow index 推板导柱 guide pin for ejector plater 座板 clamping plate 垫块 space block(plate) 推板 ejector block(plate) afdek plate 档尘板 guide stripe 行位后板 cavity sub-insert 前模镶件 core sub-insert 后模镶件 sprue puller insert 扣针镶件 stage ejector 顶棍 spacer rock(risers) 间隔板变形 distortion 弯曲 warp 拖花 drag marks 火花纹 EDM marks 困气 venting 烧黑 burns 表面缩水 shrinkage 料位过薄/砸穿 thin wall stock 走水不平行 uneven fill pattern 夹水纹/流纹 witness line;mismatch;stress marks 走水纹 knit lines 走水不齐 short shots orifice 料口 nozzle seat 热嘴垫圈 nozzle plate 射嘴板 cross pin 十字头销 sled 射台 seal ring 封密圈 spacer rail 介子座 heater groove 发热管槽 heater cement 发热管的结合剂 soak 浸泡 seat 垫圈 ream 铰大圆孔直径 grind 磨床 drill 钻床 mill 铣床 caliper 卡尺 G-caliper 分厘卡 Depth Gauge 深厚计 hardness tester 硬度计 angle gauge 角规 marble table 云台石 projector 投影仪 height gauge 高度仪 microscope 显微镜 plug gauge 塞规 leveller 水平器 R gauge R 规 Inter caliper 内分厘卡 surface 平面仪 item number 细目编码 catalog number 材料分类编码 undercut lip 倒扣口 hot tip = hot drop = nozzle 热嘴 blow-off strip 放气板 blow-off nozzle 吹风口 spiral hose 螺旋式的连接喉 rust solvent 除锈剂 shaft 曲轴 tensile strength 拉伸力 yield strength 屈服力 spark erosion 电火花蚀刻 etch(photo-etch) 电蚀 harden 淬硬 copper electrode 铜公 corrosion resistance 耐腐蚀 anneal 退火 heat treatment 淬火 FEM(finite elemnet method) 有限元法 preliminary tool design 初期模具设计图 zone 热流道区域 reverse taper 倒啤把 clamp plate 码板 toggle clamp 快速夹 vacuum furnace 真空炉 cavity insert rounds 圆柱镶件 cavity insert b0locks 方柱镶件 tensile strength 抗张强度,抗拉强度 Concept drawing 概念图 Assembly drawing 装配图 mismatch;witness line 夹纹 shut-off(n.) 枕位 venting valves 疏气阀 venting plug 疏气塞 valve casing 阀门罩 twist drill 旋钻 harden/nitride 碎硬 anneal 退火 temper 回火 stess crack 应力断裂 corrosion resistance 防腐,防锈 tensile strength 物】抗张强度,抗拉强度 split mould (分离)组合式的模具 inclined plate 斜面 inclined bolt 斜栓 jaw (工具,机械等)夹住东西的部分,钳口 step change of the P/L 分形面枕位的改变 thin steel section 较薄的料位 clean-up 清理,清除,清扫 Mold Dating Insert 模具日志镶件 Hot Sprue Bushing 热浇口套 semi-automatic 半自动 quick disconnector 快速断开接头 full shot 足量注射 mismatch 夹痕;夹水纹 ejector mark 顶痕 screw boss 螺丝孔,螺丝基座 sink mark 缩坑 15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂 drag mark 拖痕 stress mark 应力痕 reinforcement rib 加强筋 slght stoning 轻度磨砂 soliid line 实线 dotted line 虚线 internal diameter 内径 external diameter 外径 nickel-plated 电镀的 handling hole;lifting hole 吊装孔 parallel 平行块 piston 活塞 plunger 柱塞 carrier 导轨 rest 支架 item number 项目编号 catalog item 商品目录编码 dimensional datum 尺寸基准 heat treatment certification 淬硬证明文件 back-up bushing 支撑导套 jacking screw 起重螺丝,千斤顶 tapped hole (带有螺旋角度的)螺丝孔 diagonal corner 成对角的角落 burn mark 烧痕 hot runner mainfold (热流道板)分流板 texuring 蚀纹 clamping screw (注塑机)码模螺丝 imperial 英制的 metric 公制的 puller bushing 水口套 puller bar 水口铁 drool bushing 防漏胶套筒 safety switch 限位制 water line connected internally or hard tubing 不可用胶喉连接运水 lifter: on square rod or locked from rotation 用方形柱或用管钉防止斜顶转动 gate insert 入水镶件 gate shut-offs 流道开关配件 guided ejection 中托司 parting line shutoff 前后模接触面 waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值 spacer 垫块 pocket 挖槽 rough 粗加工 finish 精加工 plunge rate 进刀率 retract rate 提刀速率 splindle rate 主轴转速 coolant 冷却液 SPLIT RING 开口环(钥匙圈) 侧向抽芯力 side pulling-core force convert.transfer 转图 guide pin 边针 Tee slot cutter T形SLOT CUTTER zigzag 双向切削 constant overlap spiral 等距环切 parallel spiral 环绕切削 parallel spiral clean corners 环切并清角 morph spiral 依外形环绕 true spiral 螺旋切削 one way 单向 end mill 平铣刀 spher mill 球刀 bull mill 圆鼻刀 face mill 面铣刀 rad mill 圆角成型刀 chamfer mill 倒角刀 slot mill 槽刀 taper mill 推拔铣刀 dove mill 鸠尾铣刀 lot mill 棒状 drill 钻孔 reamer 纹刀 bore bar 搪刀 tap RH 右牙刀 Tap LH 左牙刀 ctr Drill 中心钻 spot drill 点钻 cntr bore 沉头孔刀 c. sink 鱼眼孔钻 loft surface 举升曲面 coons surface 昆氏曲面 ruled surface 直纹曲面 revolved surface 旋转曲面 swept surface 扫描曲面 draft surface 牵引曲面 grinding wheel 磨砂使用的轮子 quench steel 将...淬火,使冷却 stress relieving 应力消除 molten 熔热的 oxide film 氧化层 guide pin and sleeve, locating ring ,ejector ,ejector balde, ejector sleeve,lifters, wear plate,horn pin,O ring, water baffle, water pipe plug,water line connector,wear plate ,air cylinder,hydraulic cylinder, micro switch,oil nipple, spring,sprue bushing,early return system, accelerated ejectors, slied holder,cycle counter,date stamper, hot runner syste 导边,司筒,定位圈,顶针,扁顶针,顶针司筒,斜坊,磨损板,气顶针,O形圈,隔片,运水管道塞,运水管道转接头,氯压缸,液压缸,开关装置,油枪接头,弹弓,浇口套,早期回撞装置,加速顶针,注塑周期计数器,滑块固定板,生产日期铭牌,热流道系统 chemical composition 化学成份 thermal conductiivity 导热性能 thermal diffusivity 热扩散性能 dimensonal stablity 尺寸稳定性能 cooling effiency 冷却效率 easiler ejection 易于脱模 alloy insert 合金镶件 (cooling) duct 输送管;导管 maintenance cost 维护费用 ultrasonic testing 超声波检测 crack 断裂 direct gate 直接浇口 ring gate 环形浇口 disk gate;disphragm gate 盘形浇口 spoke gate;spider gate 轮辐浇口 pin-point gate 点浇口 edge gate 侧浇口 submarine gate;tunnel gate 潜伏浇口 fan gate 扇形浇口 tab gate 护耳浇口 runner plate 流道板(或冷或热) secondary nozzle 二级喷嘴 torpedo;torpedo body assembly 鱼雷形组合体 catridge heater 管式加热器 heat pipe 热管 valve gate 阀式浇口 force plunger;pot plunger 柱塞 flash groove;spew groove 溢料槽 impression;cavity block;cavity plate 凹模 punch;force 凸模 movable insert;loose detail 活动镶件 cavity splits;core splits(凹模拼块) (型芯拼块) 拼块 side core 侧型芯 thread plug;threaded core 螺纹型芯 thread ring;threaded cavity 螺纹型环 cutting wheel 切割砂轮 grinding wheel 打磨砂轮 abrasive material 打磨器材 mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管 pressure gauge 高压油表 hydraulic hose 压力油喉 plastic blow mould 吹塑模 plastic injection mould 注塑模 blandk&form compound die 冲扎复合模 precisiion blanking die 精密冲模 MFR=melt flow rate 熔料流动率 MFT=melt flow index 熔料流动指数 handling hole 拉铃孔 stop plate 限位块 linder bush 衬套 spacer block(plate) 垫块,方铁 back-up ring 背位环 standoff 限位块 American Safety Hoist Rings. 英制安全吊装环 Mechanical Properties 机械性能 Tensile Strength(MPa) 抗拉强度 elongation 延伸率 hardness(Brinell) 硬度 shear stength(MPa) 剪切力 impact strength 冲ren性 Physical Properties 物理性能 solidification shrinkage 凝固收缩率 freezing range 凝固与熔范围 thermal expansion 热膨胀系数 specific heat 比热 thermal conductivity 热导率 e

展开阅读全文