定时器85190.doc

RR定时器（MS侧）：TimerStartStopAt expiryT300Transmission of RRC CONNECTION REQUESTReception of RRC CONNECTION SETUPRetransmit RRC CONNECTION REQUEST if V300 = N300, else go to Idle modeT302Transmission of CELL UPDATE/URA UPDATEReception of CELL UPDATE CONFIRM/URA UPDATE CONFIRM Retransmit CELL UPDATE/URA UPDATE if V302 = N302, else, go to Idle modeT304Transmission of UE CAPABILITY INFORMATIONReception of UE CAPABILITY INFORMATION CONFIRMRetransmit UE CAPABILITY INFORMATION if V304 = N304, else initiate a cell update procedureT305Entering CELL_FACH or URA_PCH or CELL_PCH state. Reception of CELL UDPATE CONFIRM/URA UPDATE CONFIRM. Entering another state.Transmit CELL UPDATE if T307 is not activated and the UE detects in service area. Otherwise, if T307 is not active, start T307.T307When the timer T305 has expired and the UE detects out of service area.When the UE detects in service area.Transit to idle modeT308Transmission of RRC CONNECTION RELEASE COMPLETENot stoppedTransmit RRC CONNECTION RELEASE COMPLETE if V308 =N308, else go to idle mode. T309Upon reception of CELL CHANGE ORDER FROM UTRAN messageSuccessful response to a connection establishment request in the new cell. Resume the connection to UTRANT310Transmission of PUSCH CAPACITY REQUESTReception of PHYSICAL SHARED CHANNEL ALLOCATIONTransmit PUSCH CAPACITY REQUEST if V310 = N310, else procedure stops.T311Reception of PHYSICAL SHARED CHANNEL ALLOCATION message with the CHOICE PUSCH allocation set to PUSCH allocation pending.Reception of PHYSICAL SHARED CHANNEL ALLOCATION message with CHOICE PUSCH allocation set to PUSCH allocation assignment.UE may initiate a PUSCH capacity request procedure.T312When the UE starts to establish dedicated CHWhen the UE detects N312 in sync indication from L1. The criteria for physical channel establishment failure is fulfilledT313When the UE detects consecutive N313 out of sync indication from L1.When the UE detects consecutive N315 in sync indication from L1.The criteria for Radio Link failure is fulfilledT314When the criteria for radio link failure are fulfilled.The timer is started if radio bearer(s) that are associated with T314 exist of if only RRC connection exists.When the Cell Update procedure has been completed.See subclause 8.3.1.13T315When the criteria for radio link failure are fulfilled.The timer is started only if radio bearer(s) that are associated with T315 exist.When the Cell Update procedure has been completed.See subclause 8.3.1.14T316When the UE detects out of service area in URA_PCH or CELL_PCH stateWhen the UE detects in service area.Initiate cell update procedure if in service area is detected. Otherwise start timer T317, transit to CELL_FACH state and initiate cell update procedure when the UE detects in service area.T317When the T316 expires or when in CELL_FACH state, the UE detects out of service area.When the UE detects in service area.Transit to idle modeMM定时器（MS侧）：TIMERNUM.MMSTATTIMEOUTVAL.CAUSE FOR STARTNORMAL STOPAT THE EXPIRYT3210320s-LOC_UPD_REQ sent- LOC_UPD_ACC-LOC_UPD_REJ-AUTH_REJ-Lower layer failureStart T3211T32111215s-LOC_UPD_REJ with cause#17 netw. failure-lower layer failure or RR conn. released after RR conn. abort during loc. updating-Time out-cell change-request for MM connection establishment-change of LARestart the Location update proc.T32121,2Note 1-termination of MM service or MM signalling-initiation of MM service or MM signallinginitiate periodic updatingT321312114s-location updating failure-expiry-change of BCCH parameternew random attemptT321435720sAUTHENT FAILURECause = MAC failure or GSM authentication unacceptable sent AUTHENT REQ receivedConsider the network as false (see 4.3.2.6.1)T321635715sAUTHENT FAILURECause = Synch failure sentAUTHENT REQ receivedConsider the network as false (see 4.3.2.6.1)T321835720sRAND and RES stored as a result of of a UMTS authentication challenge-Cipher mode setting (A/Gb mode only)- Security mode setting (Iu mode only) - CM_SERV_ACCEPT received - CM SERVICE REJECT received-LOCATION UPDATING ACCEPT received-AUTHENT REJ received-AUTHENT FAIL sent-enter MM IDLE or NULLDelete the stored RAND and REST322075s-IMSI DETACH-release from RM-sublayerenter Null or Idle, ATTEMPTING TO UPDATET3230515s-CM SERV REQCM REEST REQ-Cipher mode setting-CM SERV REJ-CM SERV ACCprovide release ind.T324091010ssee subclause 11.2.1see subclause 11.2.1abort the RR connectionT324125300ssee subclause 11.2.1see subclause 11.2.1abort the RR connectionGMM定时器（MS侧）：TIMER NUM.TIMER VALUESTATE CAUSE OF STARTNORMAL STOPON THE 1st, 2nd, 3rd, 4th EXPIRY Note 3T331015sGMM-REG-INITATTACH REQ sentATTACH ACCEPT receivedATTACH REJECT receivedRetransmission of ATTACH REQT331115sGMM-DEREG ATTEMPTING TO ATTACH orGMM-REG ATTEMPTING TO UPDATEATTACH REJ with other cause values as described in chapter GPRS Attach ROUTING AREA UPDATE REJ with other cause values as described in chapter Routing Area Update Low layer failureChange of the routing areaRestart of the Attach or the RAU procedure with updating of the relevant attempt counterT331630sGMM-REG-INITGMM-REGGMM-DEREG-INITGMM-RA-UPDATING-INTGMM-SERV-REQ-INIT(Iu mode only)RAND and RES stored as a result of a UMTS authentication challengeSecurity mode setting(Iu mode only)SERVICE ACCEPT received. (Iu mode only)SERVICE REJECTreceived(Iu mode only)ROUTING AREA UPDATE ACCEPT receivedAUTHENTICATION AND CIPHERING REJECT receivedAUTHENTICATION_AND_CIPHERING FAILURE sentEnter GMM-DEREG or GMM-NULLDelete the stored RAND and REST331820sGMM-REG-INITGMM-REGGMM-DEREG-INITGMM-RA-UPDATING-INTGMM-SERV-REQ-INIT (UMTS only)AUTHENTICATION & CIPHERING FAILURE (cause=MAC failure or GSM authentication unacceptable) sentAUTHENTICATION & CIPHERING REQUEST receivedOn first expiry, the MS should consider the network as false (see 4.7.7.6.1)T332015sGMM-REG-INITGMM-REGGMM-DEREG-INITGMM-RA-UPDATING-INTGMM-SERV-REQ-INIT (UMTS only)AUTHENTICATION & CIPHERING FAILURE (cause=synch failure) sentAUTHENTICATION & CIPHERING REQUEST receivedOn first expiry, the MS should consider the network as false (see 4.7.7.6.1)T332115sGMM-DEREG-INITDETACH REQ sentDETACH ACCEPT receivedRetransmission of the DETACH REQT333015sGMM-ROUTING-UPDATING-INITIATEDROUTING AREA UPDATE REQUEST sentROUTING AREA UPDATE ACC receivedROUTING AREA UPDATE REJ receivedRetransmission of the ROUTING AREA UPDATE REQUESTmessageTIMER NUM.TIMER VALUESTATE CAUSE OF STARTNORMAL STOPON EXPIRYT3302Default 12 minNote 1 GMM-DEREGorGMM-REGAt attach failure and the attempt counter is greater than or equalto 5.At routing area updating failure and the attempt counter is greater than or equal to 5.At successful attachAt successful routing area updatingOn every expiry, initiation of theGPRS attach procedureorRAU procedureT3312Default 54 minNote1GMM-REGIn GSM, when READY state is left.In UMTS, when PMM-CONNECTED mode is left.When entering state GMM-DEREG Initiation of the Periodic RAU procedureT3314READY(GSM only)Default 44 secNote 2All except GMM-DEREGTransmission of a PTP PDUForced to StandbyNo cell-updates are performedT3317(UMTS only)10sGMM-SERVICE-REQUEST-INITIATEDSERVICE REQ sentSecurity mode control procedure is completed,SERVICE ACCEPT received, orSERVICE REJECT receivedAbort the procedureSM定时器（MS）：TIMER NUM.TIMER VALUESTATE CAUSE OF STARTNORMAL STOPON THE 1st, 2nd, 3rd, 4th EXPIRYT338030sPDP-ACTIVE-PENDACTIVATE PDP CONTEXT REQUEST or ACTIVATE SECONDARY PDP CONTEXT REQUEST sentACTIVATE PDP CONTEXT ACCEPT or ACTIVATE SECONDARY PDP CONTEXT ACCEPT receivedACTIVATEPDP CONTEXT REJECT or ACTIVATESECONDARY PDP CONTEXT REJECT receivedRetransmission of ACTIVATE PDPCONTEXT REQ or ACTIVATE SECONDARY PDP CONTEXT REQUESTT3381 8sPDP-MODIFY-PENDINGMODIFY PDP CONTEXT REQUEST sentMODIFY PDP CONTEXT ACCEPT receivedRetransmission of MODIFY PDP CONTEXT REQUESTT33908sPDP-INACT-PENDDEACTIVATE PDP CONTEXT REQUEST sentDEACTIVATE PDP CONTEXT ACCreceivedRetransmission of DEACTIVATEPDP CONTEXT REQUESTCC定时器（MS）：TIMNUM.TIM VALSTATE OF CALLCAUSE OF STARTNORMAL STOPAT FIRST EXPIRYAT SECOND EXPIRYT30330sCall initiatedCM SER RQ sentCALL PROC, or REL COMP receivedClear the callTimer is not restartedT30530sDisconnect RequestDISC sentREL or DISC receivedREL sent.Timer is not restartedT30830sRelease requestREL sentREL COMP or REL receivedRetrans. RELEASE restart T308Call ref. releaseT310Note 130sOutgoing call ProceedingCALL PROC receivedALERT,CONN, DISC or PROG rec.Send DISCTimer is not restartedT31330sConnect RequestCONN sentCONNect ACKnowledge receivedSend DISCTimer is not restartedT32330sModify RequestMOD sentMOD COMP or MOD REJ receivedClear the callTimer is not restartedT33230sWait for network infoSTART_CC sentCC-EST. receivedClear the callTimer is not restartedT33530sCC-Est. ConfirmedCC-EST CONF.sentRECALL receivedClear the callTimer is not restartedT33610sSTART DTMF sentSTART DTMF ACK or START DTMF REJECT receivedTimer is not restartedThe MS considers the DTMF Procedure (for the digit) to be terminatedT33710sSTOP DTMF sentSTOP DTMF ACK receivedThe MS considers the DTMF procedure (for the current digit) to be terminatedTimer is not restarted