船舶英汉词汇对照表.doc

船舶设备词汇对照
[p=30, 2, left]Name Plate and Abbreviations
ITEM NO. 编号 STANDARD NO. OR DRAWING NO.标准号或图号
NAME 名称 DN 通径
PN 压力 MATERIAL 材料
NAME PLATE STD. NO. 铭牌标准 WORDS ON NAME PLATE 铭牌刻字内容
REMARKS 备注 BLIND FLANGE 盲板法兰
LEVEL INDICATOR (PLANK TYPE)板式液位计 BELL MOUTH 吸口（喇叭口/钟形口）
STOP VALVE 截止阀 SELFCLOSING
VALVE, SPRING LOADED 自闭式放泄阀
SAFETY VALVE 安全阀 STOP CHECK VALVE 截止止回阀
QUICK CLOSING VALVE, PNEUMATICALLY OPERATED 气动快关阀
DIAGRAM OF FO TRANSFER SYSTEM 燃油输送系统
DIAGRAM OF FO PURIFYING SYSTEM 燃油净化系统
DIAGRAM OF FO DRAIN SYSTEM 燃油泄放系统
SANDWICH NONRETURN
FLAP 板式止回阀
DIAGRAM OF LO TRANSFER SYSTEM 滑油输送系统
DIAGRAM OF L.O. PURIFYING SYSTEM 滑油净化系统
NO. 序号 NOM. DIA. 通径 mm
O.D. & THK. 外径 x 壁厚㎜ x ㎜ ABOUT LENGTH 近似长度
WEIGHT 重量 CLASSⅡ
Ⅱ级管
SEAMLESS STEEL 无缝钢管 SEAMLESS COPPER 无缝铜管
SLUDGE PIPE OF PURIFYING 分油机排渣管 DRAIN PIPE OF PURIFYING 分油机排水管
LO DIRTY PIPE 滑油污油管 LO CLEAN PIPE 滑油净油管
PRESS. G. CONN. PIPE 压力表接管 LO SERVICE SYSTEM 滑油日用系统
QTY. 数量 WT. 重量
NAME PLATE STD. NO. 铭牌标准
MANOVACUUMMETER
AND VALVE 压力真空表和阀
L.O. DRAIN SYSTEM 滑油泄放系统 FRESH WATER COOLING SYSTEM 淡水冷却系统
BALL COCK 浮球阀 BUTTERFLY VALVE 手动蝶阀
COMPRESSED AIR SYSTEM 压缩空气系统
HOSE VALVE 软管接头阀
E/R OIL TANK QUICKCLOSING
VALVE CONTROL SYSTEM 机舱油舱柜快关阀控制系统
APPLICATION OF PIPES 管子用途
NOM. DIA. 通径 TYPE 牌号
QUICKCLOSING
VALVE CONTROL PIPES 快关阀控制管
DRAIN PIPE 泄放管 E/R STEAM SYSTEM DIAGRAM 蒸汽系统
0.68Mpa STEAM PIPE 0.68Mpa 蒸汽管 BOILER FEED WATER PIPE 锅炉给水管
BOILER BLOWDOWN PIPE 锅炉排污管/放水管 0.68Mpa CONDENSATE PIPE 0.68Mpa 凝水管
OVERFLOW PIPE 溢流管 AIR PIPE 透气管
DRAIN PIPE 放泄管 REMOTE THERMOMETER温度计
DIAGRAM OF TANKS STEAM HEATING SYSTEM 舱柜加热系统原理图
BLANK FLANGE 盲板法兰 BILGE WATER PIPE 舱底水管
BALLAST WATER PIPE 压载水管 FIRE WATER PIPE 消防水管
DIAGRAM OF WHOLE SHIP BILGE & BALLAST SYSTEM 全船舱底、压载管系原理图
BUTTERFLY VALVE HYDRAULIC ACTUATOR 液压遥控蝶阀
DISCHARGECHECK VALVE 吸入止回阀
DISCHARGE VALVE OF SELF CLOSED 自闭式放泄阀
CAST IRON 铸铁 CAST STEEL 铸钢
OILY WATER SEPARATOR SYSTEM 舱底水油水分离器系统
BILGEWATER CLARIFIER 舱底水油水分离器
S. W. PIPE 海水管 BILGE PIPE 舱底水管
DRAIN PIPE 处理水排出管 WASTE OIL PIPE 废油管
F. W. PIPE 淡水管 STEAM/CONDEN. PIPE 蒸汽/凝水管
DIAGRAM OF E/R AIR, SOUNDING & TRANSFUSE SYSTEM 机舱空气、测深、注入管系图
AIR PIPE (WEATHER DECK) 空气管(露天甲板)
SOUNDING PIPE 测深管 DRAIN PIPE 泄放管
SHIP’S AIR SOUNDING AND FILLING 全船空气、测深、注入管系图
VENT. HEAD 空气管头 INJECT HEAD 注入接头
SOUNDING HEAD 测深头
ONE SIDE WELDED BED PLATE FOR FLANGES 法兰焊接单面座板
THE HEAD LOSS IN PIPE FROM PUMP TO THE HYDRANT OF THE HIGHEST POSITION
至最高位置处消火栓，管路水力损失
SEGMENT OF PIPE 管路编号 LENGTH OF PIPE 直管段长 L (m)
I. DIA. 管子内径 di (m) FLOWRATE 管中水流量 Q (m3/h)
MODULUS 局部阻力系数 NAME OF RESISTANCE 局部阻力名称
NU. 个数 n SING. 单个ξ
FLOW VEL. 管中水流速 v (m/s) RENAULT 雷诺数 Re
RESISTANCE TRAIT VALUE 阻力特性值 N COEFFICENT OF FRICTION 流体摩擦系数λ(Re>N)
EQUIVALENT PIPE 管子当量长度 ld (m) CALCULATING LENGTH 管子折算长度 lc (m)
HEAD LOSS IN PIPE 管段压力损失 h (MPa)
THE HEAD LOSS IN PIPE FROM PUMP TO THE HYDRANT ON THE UPPER DECK FORSIDE 至上
甲板首部消火栓处，管路水力损失 H3
DIAGRAM OF FIRE FIGHTING SYSTEM 全船消防水管系图
ASSEMBLY 组合件
ISOLATING VALVE BETWEEN FIRE MAIN AND E/R
HAWSEHOLE (P) FLUSH
HAWSEHOLE (S) FLUSH
FROM EMERGENCY FIRE PUMP
TO CARGO HOLD EJECTOR
VENT BRONZE 青铜
DIAGRAM OF E/R WATER SUPPLY SYSTEM 机舱供水管系原理图
SCREW DOWN VALVE 截止阀 SCREW DOWN STOP AND CHECK VALVE 截止止回阀
ARRANGEMENT OF WHOLE SHIP WATER SUPPLY SYSTEM 全船供水管系布置图
FLUSH VALVE 冲洗阀 STRAIGHT CONNECT VALVE 直通阀
BASIN MIX VALVE 面盆混合放水阀
DIAGRAM OF SEWAGE WATER TREATMENT SYSTEM 生活污水处理装置管系原理图
GATE VALVE 闸阀 STOP & CHECK VALVE 截止止回阀
STOP VALVE 截止阀 CHECK VALVE 止回阀[/p][p=30, 2, left]STORM VALVE 可闭立式防浪阀 TO SEWAGE DISCH. MP. (P)
SOIL TO SEWAGE TR. UNIT
CLINIC SOIL TO SEWAGE TR. UNIT
SANI. TO SEWAGE TR. UNIT
F. W. FLUSHING TO SEWAGE TR. UNIT
SEWAGE TO SEWAGE STORAGE TK. 生活污水至生活污水存放舱
SEWAGE DISCH. OVERSIDE
CUTTING PUMP IN
CUTTING PUMP OUT
SEWAGE TR. UNIT OUT
DRAINAGE DISCH. TO SEWAGE STORAGE TK.
DRAINAGE DISCH. TO MP
DRAINAGE DISCH. OVERSIDE
DISCH. OVERSIDE
DIAGRAM OF DECK SCUPPERS 甲板疏排水管系图
DECK SCUPPER PIPE 甲板疏排水管
GALV. 镀锌
ARRANGEMENT OF SEWAGE WATER SYSTEM (GREY WATER) 卫生水疏排水管系布置图（灰水）
ARRANGEMENT OF SEWAGE WATER SYSTEM (BLACK)粪便污水管系布置图（黑水）
MARINE AIR PIPE HEAD 船用空气管头 WITH FIREPROOF NET 带防火网
MECHNICAL VENTILATION LAYOUT 舱室机械通风布置图
EXHAUST NOZZLE 圆形抽风头 FIRE DAMPER 船用防火风闸
VENTILATOR COAMING
WC EXHAUST FAN 裕厕所抽风机 MUSHROOM VENTILATORS 菌形风帽
HOSPITAL EXHAUST FAN 医务室抽风机
VENT LOUVER WITH WEATHERTIGH COVER 风雨密钢质百叶
EXHAUST NOZZLE 圆形抽风头 GOOSENECK VENTILATORS 鹅颈式通风筒
MESS & MEETING EXHAUST FAN 餐厅兼会议室抽风机
LAUNDRY AND CHANGING EXHAUST FAN 西意见、更衣室抽风机
GELLY SUPPLY FAN 厨房送风风机 GELLY EXHAUST FAN 厨房抽风风机
WIRE GRILLING 通风栅 VENTILATOR COAMING 甲板接管
GALLEY PROVISION AND PROVISION STORE EXHAUST FAN 粮库，厨房，储物间抽风机
FIRE DAMPER 船用防火风闸 MUSHROOM VENTILATORS 菌形风帽
LAYOUT OF REF. MACHINE RM. VENTILATION 制冷机室通风管系布置图
REF. MACHINE EXHAUST FAN 制冷机室抽风机
VENTILATOR COAMING 甲板接管 WIRE GRILLING 通风栅
GOOSENECK VENTILATORS 鹅颈式通风筒 STAINLESS STEEL 不锈钢
TOTAL 总重 REF. PROV. PLANT SYSTEM 伙食冷库管系原理图
PRESSURE GAUGE VALVE 压力表阀 METALSHELL
THERMOMETER 金属壳水银温度计
NO. 1 CONDENSER C.S.W. INLET NO. 2 CONDENSER C.S.W. OUTLET
LAYOUT OF DECK COMPRESSED AIR PIPING 甲板压缩空气管系布置图
HOSE JOINT VALVE 软管接头阀 REDUCING VALVE 减压阀
SCREW DOWN VALVE 截止阀 SCREW DOWN VALVE 旋压阀/螺旋阀
MALE SCREW 外螺纹 EMER. GEN. ROOM 应急发电机室
A/C ROOM POOP DECK (P) 尾楼甲板（左）
POOP DECK (S) 尾楼甲板（右） CREW DECK (P) 船员甲板（左）
BOAT DECK (S) 救生艇甲板（右） CAPTAIN DECK 船长甲板
NAVIGATION DECK 驾驶甲板 UPPER DECK（P）
上甲板(左)
FORECASTLE DECK(P)首楼甲板（左） STORE 储物间
EMER. FIRE PUMP ROOM 应急消防泵室 INLET OF REDUCING VALVE 减压阀入口
TO AIR HORN 至汽笛 DRAIN
BYPASS VALVE 旁通阀 OUTLET OF RECUDING VALVE 减压阀出口
FLANGE ACCORDING TO ISO 法兰按照 ISO
SETTING 0.22MPa 设定值 0.22MPa
OXYGEN & ACETYLENE PIPING DIAGRAM 氧气/乙炔管系图
OXYGEN BOTTEN 氧气瓶组 ACETYLENE CYLINDER 乙炔瓶组
OXYGEN REDUCING VALVE 氧气减压阀
ACETYLENE BACKFIRE VALVE 乙炔回火阀
ACETYLENE REDUCING VALVE 乙炔减压阀
2 – LEFT OPENED 2 – 左开 5 – RIGHT OPENED 5 – 右开
1 – DOWN OPENED 1 – 下开
NATURAL VENTILATION LAYOUT 全船自然通风布置图
STRAINER 粗滤器，滤网,过滤器
EXPANSION BELLOW 膨胀伸缩式波纹管
SLEEVE 套管
伸缩的 TELESCOPIC/RETRACTILE
EXTENSION LADDER 伸缩梯
Buffer 缓冲器
Adjust valve 调节阀
OIL AND AIR SEPARATOR OF BOILER
FO PUMP OF BOILER
FO PUMP OF BOILER
FO BOOSTER MODULE
STEAM TRACE INLET DN10
PIPING SYMBOL: 管子符号
MGO PIPE: 燃料油管
轻柴油管：
STEAM TRACE PIPE: 蒸汽伴行管：
MGO SERVICE TK 轻柴油日用舱
HFO SERVICE TK 燃料油日用舱
NO.2AUX.ENGINE GEN.SETNO.2 柴油发电机组
FR. RETURN OIL OF SPRAY 喷油回油
NO.1AUX.ENGINE GEN.SETNO.1 柴油发电机组
HFO SERV.TK OF BOILER 锅炉燃料油日用柜
MDO TK OF BOILER 锅炉点火轻柴油柜
FO BOOSTER MODULE 燃油供油单元
粗滤器 FILTER
燃油供给泵 FO SUPPLY PUMP
调压阀 REGULATING PRESS. VALVE
手动逆洗滤器 HAND BACK FLUSH FILTER精滤器 FINE FILTER
流量计 FO FLOW METER
空气分离器 AIR SEPARATOR
燃油循环泵 FO CIRCULATING PUMP
燃油加热器 FO HEATER
自动排气浮阀 AUTO. DEGAS VALVE
控制屏 CONTROL PANEL
均质机 OMEGAFIRE
三通切换阀 THREE WAY VALVE
粘度传感器 VSICOSITY SENSOR
蒸汽控制阀 STEAM CONTROL VALVE
HAND QUICKCLOSING
VALVE 手动快关阀
FO AND EXCUSED BOILER 燃油废气组合锅炉
DIAGRAM OF FO SERVICE SYSTEM 燃油日用系统
供油单元柴油进口 FO INLET OF FO BOOSTER MODULE
供油单元燃料油进口 HFO INLET OF FO BOOSTER MODULE
供油单元加热蒸汽进口 STEAM INLET OF FO BOOSTER MODULE
供油单元加热蒸汽冷凝水出口 COAGULATE WATER OUTLET OF FO BOOSTER MODULE
供油单元精滤器残油泄放口
LEAKAGE OIL OUTLET OF THIN STRAINER OF FO BOOSTER MODULE
供油单元燃油出口 FO OUTLET OF FO BOOSTER MODULE
供油单元燃油回油接口 RETURN OIL OUTLET OF FO BOOSTER MODULE
供油单元泄放口 1 No.1 LEAKGE OIL OUTLET OF FO BOOSTER MODULE
供油单元泄放口 2 No.2 LEAKGE OIL OUTLET OF FO BOOSTER MODULE
供油单元回油筒放气口 AIR OUTLET OF MIXING TANK OF FO BOOSTER MODULE
TECHNICAL REQUIREMENTS
1. ANNOTATED SIZES OF PIPE IN THE DRAWING ARE OUT DIA.xTHICK(mm).
2. HERE PIPES PENETRATE THROUGH WATER TIGHT BULKHEADS OR DECK TO BE FITTED
WITH PENETRATION PIECE ACCORDING TO CB/T348092.
3. ALL PIPING TO BE SECURELY SUPPORTED AND BRACED IN ACCORDING WITH CB/T37801997
OR SHIPYARD STANDARD.
4. THE ITEMS WITH `` * '' OR `` '' TO BE SUPPLIED WITH EQUIPMENT.
5. HYDROSTATIC TEST:
DESIGN PRESS. MPa
BEFORE INSTALLATION MPa
AFTER INSTALLATION MPa
HFO PIPE 燃料油管
MGO PIPE 轻柴油管
6. THE MARK Item mark/Item No. REFER TO LIST OF AUTOMATIC
CONTROL、MONITORING & ALARM POINTS FOR E/R(44001MX).
7. THE H.F.O. PIPING MUST BE PROVIDED WITH DN10(∅ 15X1.5) STEAM TRACING
PIPE AND TO BE COVERED WITH GLASS WOOL OR OTHER EQUIVALENT.
技术要求
1. 图中管子所注尺寸均为外径 x 壁厚(mm)。
2. 管子通过水密舱壁,甲板或舱壁时,应按 CB/T348092
或船厂标准设置通舱管件。
3. 管子应按 CB/T37801997
或船厂标准设置牢固的支架，管卡。
4. 图中带``*''或
符号为设备所带附件。
5. 液压试验: 设计压力Mpa, 装船前 Mpa 装船后 MPa
6. 图中自动化符号
项目代号/项目序号
详见"轮机自动化项目明细表"
7. 燃料油管系需设 DN10(∅ 15X1.5)蒸汽伴行管,在外包覆玻璃棉或其它适当的绝热材料.
DIAGRAM OF FO TRANSFER SYSTEM 燃油输送系统
'STANDARD NO. OR DRAWING NO. 标准号或图号
'DN '通径 mm
NAME PLATE STD. NO. 铭牌标准 CB/T841998
PN 压力 Mpa
QTY.数量
WT.重量 kg
轮机说明书 SPECIFICATION OF MACHINERY PART
生
产
设
计 PRODUCTION DESIGN
NOTES: 说明：
1. ALL DUCT SHOULD BE FIXED WITH HANGER .THE DISTANCE BETWEEN TOWHANGERS
IS 2 METERS MAXIMUM.
风管至多每隔 2 米设一固定吊架。
2. ALL VENTLATORS SHOULD BE INSTALLED WITH RATPROOF WIRES.
所有通风筒应设有防鼠网。
3. AFTER FITTED ON BOARD,THE OUTSIDE SURFACE OF NON GALVANIZED FITTINGS AND
DUCT SHOULD BE PAINTED 2 COATS OF RUST PREVENTIVE PAINT AND1 COAT OF
FINISHING PAINT.
凡是没有镀锌的附件及管道，在装船后，其表面应涂防锈漆 2 度及色漆 1 度。
4. THE FLANGES UESD FOR RECTANGULAR DUCTS IN THIS DRAWING SHOULD BE MADE
IN ACC. WITH GB156179.
风管法兰按 GB156179
设置。
5. PENETRATING PIECES USED FOR DUCTS TO PASS THROUGH THE A CLASS BULKHEAD
OR DECK SHALL BE PROVIDED IN ACC. WITH "FIRE RESISTING DIVISION PLAN " (10304)
and "TYPICAL NODE OF FIRE RESISTING STRUCTURE"(36202).
风管穿过 A 级舱壁或甲板的贯通件按《防火分隔图》(10304)
和《典型防火节点图》(36202)
设
置。
6. PENETRATION HAS TO BE INSULATED ACC. THE REQUIRED FIRE INTEGRITY OF THE
BULKHEAD/DECK.
贯通件按照它所穿越的舱壁或甲板的防火等级进行绝缘
。
7. THE LOWEST DUCT OF SHIP STRUCTURE SHOULD BE OPENED HOLE, AS TO BE DRAIN
WATER.
在通风静压箱的最低处开泄水孔。
CADET 甲板见习生
DECK STORE 甲板物料间
HOSPITAL 医务室
A/C ROOM 空调机室
UPPER DECK 上甲板
GALLEY STORE 厨房储物间
POOP DECK 尾楼甲板
STEEL PLATE 钢板
GALVANIZED STEEL 镀锌钢板
ASSEMBLY 组合件
DUCT 风管
WIRE GRILLING 通风栅
VENTILATOR COAMING 甲板接管
EXHAUST FAN 轴流抽风风机
GOOSENECK VENTILATORS 鹅颈式通风筒
MUSHROOM VENT. HEAD 菌形通风筒
LAYOUT OF AIR CONDITION ROOM 空调机室通风布置图
DETAIL DESIGN 详
细
设
计
REVERSIBLE 可逆转
NOTES: 说明：
1. ALL DUCT SHOULD BE FIXED WITH HANGER .THE DISTANCE BETWEEN TOW HANGERS
IS 2~3 METERS MAXIMUM.
风管至多每隔 2~3 米设一固定吊架。
2. ALL VENTLATORS SHOULD BE INSTALLED WITH RATPROOF WIRES.
所有通风筒应设有防鼠网。
3. AFTER FITTED ON BOARD,THE OUTSIDE SURFACE OF NON GALVANIZED FITTINGS AND
DUCT SHOULD BE PAINTED 2 COATS OF RUST PREVENTIVE PAINT AND 1 COAT OF
FINISHING PAINT.
凡是没有镀锌的附件及管道，在装船后，其表面应涂防锈漆 2 度及色漆 1 度。
4. THE FLANGES UESD FOR RECTANGULAR DUCTS IN THIS DRAWING SHOULD BE MADE
IN ACC. WITH GB156179.
风管法兰 GB156179
设置。
5. PENETRATING PIECES USED FOR DUCTS TO PASS THROUGH THE A CLASS BULKHEAD
OR DECK SHALL BE PROVIDED IN ACC. WITH "FIRE RESISTING DIVISION PLAN " (10304)
and "TYPICAL NODE OF FIRE RESISTING STRUCTURE"(36202).
风管穿过 A 级舱壁或甲板的贯通件按《防火分隔图》(10304)
和《典型防火节点图》(36202)
设置。
6. PENETRATION HAS TO BE INSULATED ACC. THE REQUIRED FIRE INTEGRITY OFTHE
BULKHEAD/DECK.
贯通件按照它所穿越的舱壁或甲板的防火等级进行绝缘
。
7. THE LOWEST DUCT OF SHIP STRUCTURE SHOULD BE OPENED HOLE, AS TO BE DRAIN
WATER.
在通风静压箱的最低处开泄水孔。
TECHNICAL REQUIREMENTS
技
术
要
求
1. EQUIPMENTS,FITTINGS/ACESSORIES, BUSHINGS, CLAMPS, WARNING NOTICES AND
INSTRUCTIONS FOR THE INSTALLER IN THIS SYSTEM TO BE SUPPLIED BY MAKER. AND
TO BE OF APPROVE TYPE. WARNING NOTICES TO BE PROVIDED AS PER NS 6033
本系统设备，附件，通舱套管，管夹，警告牌及安装要求等均由设备商提供，且应为认可型。警告牌按标准提供。
2. THE CONNECTION OF PIPES TO BE BUTT WELDED AND TO BE LAID WITH FEW JOINTS
AS POSSIBLE.THE PATH OF PIPE PASSAGE AND MOUNTED POSITION OF BULKHEAD
PENETRATION ARE DETERMINED AT SITE.
管路连接采用对接焊形式，要求尽量减少接头，管路穿越的路径及通舱件的安装位置由现场定。
3. THE PIPES TO BE FASTENED TO THE BULKHEAD WITH PIPE CLAMPS AT INTERVALS NOT
EXCEEDING 2.5m.
管子沿舱壁布置，且每隔 2.5m 左右设一个管夹。
4. PIPE & FITTINGS TO BE CLEANED IN SHOP SO TO REMOVE RUST GREASER ETC. BY
DEGREASING WITH TRICHLOROE THANG OR ANOTHER EQUALLY EFFECTIVE AGENT
(PETROL MUST NOT BE USED) TO BE USED, AFTER DEGEASING THE PIPES TO BE RISED
WITH 10% SOLUTION OF TRISODIUMPHOSPHATE IN WATER, WITH 10% SOLUTION OF
TRISODIUMPHOSPHATE IN WATER,
管子和附件应在车间用三氯乙稀或其他等效化学剂（不能用汽油）除锈，除油；除油后用 10%磷
酸三钠溶液冲洗。
5. BEFORE MOUNTING ON SHIP, PIPE & FITTINGS TO BE BLOWN WITH NITROGEN,
COMPRESSED AIR OR OXYGEN MUST NOT BE USED.
船上安装前，需用氮气吹洗管子，附件，绝对不能使用压缩空气或氧气。
6. AFTER AII THE PIPES CONTRUCTED ON BOARD, TO SEAL TEST AS FOLLOWS:
全部管路在船上施工后进行气密试验如下：
a. AFTER INSTLLATION ON SHIP PIPES TO BE BLOWN CLEAN WITH NITROGEN AT A
PRESSURE OF ABT 0.3MPa,WHICH TO BE INCREASED UP TO ABT 1.0MPa FOR ABOUT 10
MINUTES.
管路安装后，用压力约为 0.3MPa 的氮气将管路吹净，压力在 10 分钟内逐渐升至 1.0 MPa.
b. ON THE ACETYLINE PIPING NITROGEN TO BE USED, AND THE TEST PRESSURE TO BE OF
I.O MPa. AII VALVES, JOINTS AND OTHER CONNECTIONS TO BE SWABBED WITH SOAPY
WATER. AFTER 8 HOURS, THE PRESSURE DROP SHALL NOT EXCEED 0.04MPa.
乙炔管路用压力 1.0 MPa 的氮气进行试验，抹肥皂水检查附件，接头的密封性，保持 8 小时，压
力降不得超过 0.04 MPa.
c. NON LEAKAGE OF OXYGENPIPES TO BE PERFORMED SAME AS ACETYLINE PIPES TEST
PRESSURE TO BE 1.2Mpa
氧气管路的密封试验与乙炔相同，试验压力为 1.2 MPa.
DRAWING CATALOGUE OF VENTILATION AND A/C SYSTEM
空调通风系统图纸目录
DIAGRAM OF AIR CONDITION SYSTEM 空调系统原理图
ARRANGEMENT OF AIR CONDITION ROOM 空调机室布置图
REF. PROV. PLANT SYSTEM 伙食冷库系统原理图
LAYOUT OF PIPING AND EQUIPMENT FOR PROV. CHAMMBER 伙食冷库设备、管系布置图
LAYOUT OF CARGO HOLD AND PIPE TUNNEL VENTILATION 货舱、管弄通风布置图
VENTPIPE
INSTALLTING DRAWING OF SUBSECTION 601 分段通风管安装图
LAYOUT OF CARPENTRY ROOM/FWD WINDLASS CONTROL PANEL ROOM VENTILATION
木工间、锚机控制室通风布置图
LAYOUT OF BOW THRUSTER/EMERG.FIRE PUMP VENTILATION 艏侧推舱/应急消防泵舱通风布置图
LAYOUT OF PAINT STORE VENTILATION 油漆间和储物间通风布置图
VENTPIPE
INSTALLTING DRAWING OF SUBSECTION 603 分段通风管安装图
VENTPIPE
INSTALLTING DRAWING OF SUBSECTION 608 分段通风管安装图
DUCT INSTALLING DRAWING OF UPEER DECK 上甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF POOP DECK 艉楼甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF CREW DECK 船员甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF BOAT DECK 艇甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF CAPTAIN DECK 船长甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF NAVIGATION DECK 驾驶甲板螺旋风管安装图
DUCT INSTALLING DRAWING OF DUCT TUNNEL AREA 空调管弄螺旋风管安装图
marine engineering drawing catalog 轮机图纸目录
Main mechanical equipments ordering list 轮机部分主要机械设备订货明细表
Engine room arrangement plan 机舱布置图
Ventilation arrangement plan 机舱通风布置图
High sea water box fitting plan 机舱高位海水箱装置图
Low sea water box fitting plan 机舱低位海水箱装置图
Diesel generator unit base frame with ID 柴油发电机组座架及安装图
The arrangement of bow thruster & emerg fire pump tank 艏侧推舱/应急消防泵舱布置图
Steering gear room arrangement plan 舵机舱布置图
Emergency generator room arrangement plan 应急发电机室布置图
Emergency generator base frame with ID 应急发电机座架及安装图
Side rudderstocks 边舵柄/杆
Tank high, low water level alarm arrangement plan 舱柜高、低液位报警布置图
ARRANGEMENT OF CO 2 ROOM CO 2 站室布置图
Emergency fire pump tank SW box fitting drawing 应急消防泵舱海水箱装置图
marine engineering drawing catalog 轮机图纸目录
Engine room arrangement plan 机舱布置图
Smoke piping arrangement plan 机舱排烟管系布置图
Ventilation arrangement plan 机舱通风布置图
High sea water box fitting plan 机舱高位海水箱装置图
Low sea water box fitting plan 机舱低位海水箱装置图
Diesel gen