二十种变送器的标定步骤.docx

1EJA1.设备设置device setup2.诊断与服务diag/service3.校验calibration4.传感器的校验sensor trim2E+H质量流量计1.GROUP SELECT 快速设置2.process parameter 工艺参数3.zero PT ADJ 零点标定3电磁流量计1.setup2.process input3.calibration4.autom.zero calib空管标定4244LD浮筒液位计1.diagnosis2.zero trim 清零3.trimmedaccept清零5艾默生质量流量计17001.service tools 服务工具2.maintenance 维护3.zero calibration 调零4.perform auto zero 执行调零63051C变送器1.maintenance 维护 保养2.pressure calibrationzero压力校验零点7ABB 2600T-266MV1.calibration 校验2.3.pressuresensor压力传感器4.5.zerotrim清零6.8ABB 2600T-262 2641.configure 组态2.3.diag/service诊断/服务4.5.zerotrim清零6.9ABB 2611.device setup 设备设置2.3.diag/service诊断/服务4.5.calibration 校验6.7.zerotrim清零8.10霍尼韦尔ST7001.device setup 设备设置2.3.calibration 校验4.5.calibration methods 校验6.7.zerotrim清零8.11霍尼韦尔ST30001.device setup 设备设置2.3.diag/service诊断/服务4.5.calibration 校验6.7.zerotrim清零8.12Promass 101.进入应用2.3.传感器4.5.传感器调整6.7.零点调整，进入零点调整控制参数8.9.启动零点调整，一般进行3次10.13Promass 300/5001.设置2.3.高级设置4.5.传感器调整6.7.零点校正8.9.启动10.14Promass 801.GROUP SELECTMEASURINGVALUES2.3.GROUPSELECTPROCESSPARAMETER4.5.ZEROPOINTADJUSTCANCEL6.7.START8.9.ACCESSCODE(密码0080）10.11.ZEROPOINTADJUSTSTART启动零点调整12.13.SURE再次确认14.15.ZEROPOINTADJUSTRUNNING 零点运行16.15Promass831.MEASURED VARIABL2.3.BASICFUNCTION基本功能4.5.PROCESSPAPAMETER6.7.ADJUSTMENT8.9.CANCEL10.11.ACCESSCODE(密码0083)12.13.START14.15.YES16.16Prosonic 931.MEASURED VARIABL2.3.BASICFUNCTION基本功能4.5.PROCESSPAPAMETER6.7.ADJUSTMENT8.9.CANCEL10.11.ACCESSCODE(密码0083)12.13.START14.15.YES16.17科隆IFC100电磁流量1.quick setup 快速设置2.3.processinput4.5.zerocalibration零点校验6.7.automatic8.18科隆IFC300电磁流量1.quick setup 快速设置2.3.processinput4.5.zerocalibration零点校验6.7.automatic8.19科隆IFC050电磁流量1.quick setup 快速设置2.3.processinput4.5.zerocalibration零点校验6.7.automatic8.20科隆MFC400电磁流量1.quick setup 快速设置2.calibratezero零点标定3.automatic4.factorycalibra.出厂标定