浮筒液位计调试菜单.pptx

单击此处编辑母版标题样式,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,2015-04-14,#,浮筒液位计调试菜单,1 Overview,概述,1 Device Status,设备状态,2 Comm Status,通信状态,3 PV is PV,是,4 Primary Variable,基本参数,5 AO,6 Process Temperature,过程温度,7 Device Information,设备信息,1 Refresh Alerts,恢复报警信号,2 No Active Alerts,没有报警信号,1 PV Value PV,值,2%Range%,范围,1 Proc Temp Source,过程温度来源,2 Proc Temp,过程温度,1 Identification,确认,2 Revisions,修正,3 Alarm Type and Security,报警类型和安全,1 HART Tag HART,标号,2 Distributor,经销商,3 Model,模型,4 Device ID,设备,ID,5 Instrument Serial Number,仪器序列号,6 Sensor Serial Number,传感器序列号,7 Final Assembly Number,最终序列号,8 Date,日期,9 Descriptor,描述符,9 Message,信息,1 HART Universal Revision HART,通用版本,2 Field Device Revision,现场设备修改,3 Firmware Revision,固件版本,4 Hardware Revision,硬件版本,5 DD Information DD,信息,1.4,1.1,1.6,1.7.1,1.7.2,1 Alarm Type,报警类型,2 Security,安全,1.7.3 Alarm Type and Security,报警类型和安全,1 Alarm Jumper,报警跳线,2 Display Alert/Saturation Level,显示报警,/,饱和极限,1 Write Lock,写入锁,2 Write Lock Setup,写入锁设置,1.7,内部使用，发现不对的与我联系修改。刘福斌,2 Configure,组态,1 Guided Setup,设置向导,2 Manual Setup,手动设置,3 Alert Setup,报警设置,4 Communications,通信,5 Calibration,校准,1 Instrument Setup,仪器的设置,1 Sensor,传感器,2 Variables,变量,3 Process Fluid,过程流体,4 Identification,确认识别,5 Instrument Display,仪表显示,2.2,2.1,1 Sensor Units,传感器单元,2 Sensor Dimensions,传感器尺寸,3 Torque Tube,扭力管,4 Instrument Mounting,仪表支架,5 Sensor Damping,传感器阻尼,2.2.1,1 Length Units,长度单位,2 Volume Units,体积单位,3 Weight Units,重量单位,4 Torque Rate Units,扭力角单位,5 Temperature Units,温度单位,2.2.1.1,1 Displacer Length,浮筒长度,2 Displacer Volume,浮筒体积,3 Displacer Weight,浮筒重量,4 Driver Rod Length,浮筒杆长度,1 Torque Rate,扭力管刚度,2 Change Torque Rate,改变扭力管刚度,3 TT Material,扭力管材质,4 TT Comp Selection,选择扭力管放大器,5 TT Comp Table,扭力管放大器平面,2.2.1.3,1 Primary Variables,主要变量,2 Sensor Limits,传感器极限,3 Primary Variable Range,主要变量范围,4 PV Damping,当前值阻尼,2.2.2 Variables,变量,1 PV is,测量值,2 Change PV,改变当前值,3 PV Units,测量值单位,4 Level Offset,液位偏差值,5 Set Level Offset,设置液位偏差值,2.2.2.1,1 Upper Sensor Limit,传感器上限,2 Lower Sensor Limit,传感器下限,3 Minimum Span,最小跨距,1 Upper Range Value,上限值,2 Lower Range Value,下限值,3 View/Change AO Action,改变电流,2.2.2.2,2.2.2.3,2.2.1.2,1 left of displacer,左侧安装,2 right of displacer,右侧安装,1 Process Fluid,过程流体,2 Process Temperature,过程温度,2.2.3 Process Fluid,过程流体,（,If PV is Level,当前值是液位）,1 Lower Fluid Density,下层介质密度,2 View Fluid Tables,流体视图表,3 Enter Constant Density,输入常数密度,4 Measure Density,测量密度,Lower Density Table,下层密度表,1 Proc Temp Source,过程温度源,2 Change Proc Temp,改变过程温度,3 Proc Temp,过程温度,4 RTD Wire Resistance,RTD,线电阻,1 Process Fluids,过程流体,2 Process Temperature,过程温度,2.2.3 Process Fluid,过程流体,（,if PV is Interface,当前值是界位）,1 Upper Fluid Density,上层介质密度,2 Lower Fluid Density,下层介质密度,3 View Fluid Tables,流体视图表,4 Enter Constant Density,输入常数密度,5 Load Steam Tables,调用负荷表,1 Upper Density Table,上层密度表,2 Lower Density Table,下层密度表,1 Proc Temp Source,过程温度源,2 Change Proc Temp,改变过程温度,3 Proc Temp,过程温度,4 RTD Wire Resistance,RTD,线电阻,2.2.3 Process Fluid,过程流体,（,if PV is Density,当前值是密度）,1 HART Tag HART,标号,2 Date,日期,3 Descriptor,描述符,4 Message,信息,5 Polling Address,登记地址,6 Physical Signaling Code,物理信号代码,7 Number of Request Preambles,数量请求前言,8 Serial Numbers,序列号,2.2.4 Identification,确认识别,1 Instrument Serial Number,仪器序列号,2 Sensor Serial Number,传感器序列号,3 Final Assembly Number,最终序列号,1 LCD Configuration,显示组态,2 Display Mode,显示模式,3 Change Display Mode,改变显示模式,4 Decimal Places,小数位,2.2.5 Instrument Display,仪表显示,2.3 Alert Setup,报警设置,1 Primary Variable,主要变量,2 Temperature,温度,1 Primary Variable Hi,主变量高报警,2 Primary Variable Lo,主变量低报警,3 Upper Range Value,上范围值,4 Lower Range Value,下范围值,5 PV Alerts Threshold Deadband,报警阈值死区,1 Hi Alert,高报警,2 HiHi Alert,高高报警,1 PV Hi Alert Enable,高报警启用,2 PV Hi Alert Threshold,高报警阈值,3 PV Hi Alert Threshold(Method),高报警阈值方法,1 PV HiHi Alert Enable,高高报警启用,2 PV HiHi Alert Threshold,高高报警阈值,3 PV HiHi Alert Threshold(Method),高高报警阈值方法,1 Lo Alert,低报警,2 LoLo Alert,低低报警,1 PV,Lo,Alert Enable,低报警启用,2 PV Lo Alert Threshold,低报警阈值,3 PV Lo Alert Threshold(Method),低报警阈值方法,1 PV,Lo,Lo,Alert Enable,低低报警启用,2 PV Lo Lo Alert Threshold,低低报警阈值,3 PV Lo Lo Alert Threshold(Method),低低报警阈值方法,2.3.2.1 Lo Alert,2.3.2,Temperature,温度,1 Instrument Temperature,仪表温度,2 Process Temperature,过程温度,1 Hi Alert,高报警,2 Lo Alert,低报警,3 Inst Temp,瞬时温度,4 Inst Temp Offset,瞬时温度偏差值,1 Inst Temp Hi Alert Enable,仪器温度高报启用,2 Inst Temp Hi Alert Threshold,仪器温度高报阈值,1 Inst Temp,Lo,Alert Enable,仪器温度低报启用,2 Inst Temp Lo Alert Threshold,仪器温度低报阈值,1 Hi Alert,高报警,2 Lo Alert,低报警,3 Proc Temp,过程温度,4 Proc Temp Offset,过程温度偏差值,1,Proc,Temp Hi Alert Enable,过程温度高报启用,2 Proc Temp Hi Alert Threshold,过程温度高报阈值,1,Proc,Temp,Lo,Alert Enable,过程温度低报启用,2 Proc Temp Lo Alert Threshold,过程温度低报阈值,2.4 Communications,通信,1 Burst Mode,脉冲模式,2 Burst Options,脉冲选项,2.5 Calibration,校准,1 Primary,主要,2 Secondary,次要,1 Guided Calibration,引导校准,2 Full Calibration,完整校准,3 Partial Calibration,部分校准,1 Min/Max Calibration,小,/,大校准,2 Two Point Calibration,两点校准,3 Weight Calibration,重量校准,1 Capture Zero,捕捉零点,2 Trim Gain,修正增益,3 Trim Zero,修正零点,1 Temperature Calibration,温度校准,2 Analog Output Calibration,模拟输出校准,1 Trim Instrument Temperature,修正仪器温度,2 Trim Processs Temperature,修正过程温度,(Visible if Process Temperature is not Manual,）,1 Scaled D/A/Trim,比例修正,D/A,3 Service Tools,服务工具,1 Active Alerts,有效报警,2 Variables,可变因素,3 Maintenance,维护,1 No Active Alerts,无效报警,(Visible if there are no active alerts),1 Refresh Alerts,刷新报警,(Visible if an alert is active-alert name plus description will be visible if the associated alert is active),1 PV,测量值,2 Primary Variable,主要变量,3 AO,模拟输出,4 Inst Temp,仪器温度,5 Process Temperature,过程温度,6 Torque Rate,扭力管刚度,7 Lower Fluid Density,下层流体密度,3.2 Variables,可变因素,（,If PV is Level,当前值是液位）,1 PV Value,当前值,2%Range%,范围,1 Proc Temp Source,源于过程温度,2 Proc Temp,过程温度,1 PV,测量值,2 Primary Variable,主要变量,3 AO,模拟输出,4 Inst Temp,仪器温度,5 Process Temperature,过程温度,6 Torque Rate,扭力管刚度,7 Upper Fluid Density,下层流体密度,8 Lower Fluid Density,下层流体密度,3.2 Variables,可变因素,（,if PV is Interface,当前值是界位,1 PV,测量值,2 Primary Variable,主要变量,3 AO,模拟输出,4 Inst Temp,仪器温度,5 Process Temperature,过程温度,6 Torque Rate,扭力管刚度,3.2 Variables,可变因素,（,If PV is Density,当前值是密度）,3.3 Service Tools,服务工具,1 Tests,测试,2 Reset/Restore,重置,/,恢复,1 LCD Test(1)LCD,测试,2 Loop Test,线路测试,1 Restore Factory Defaults,恢复工厂默认值,2 Reset Device,设备复位,1 Restore Factory Configuration,恢复工厂组态,2 Restore Factory Compensation,恢复工厂补偿,