FPC制程简介.ppt

,Confidential,Page:,*,FPC,单击此处编辑母版标题样式,单击此处编辑母版文本样式,二级,三级,四级,五级,精选课件ppt,*,FPC 製程簡介,1.Product Introduction,2.FPC產品系列應用介紹,1.1 NOTEBOOK,1.2 LCD PANEL,1.3 PDA,1.4 CELLULAR PHONE,3.原材料介紹,2.1 銅箔,2.2 Coverlay,2.3 Stiffener,2.4 Adhesive,2.5 相關測試規範,4.FPC 標準製造作業流程介紹,3.1 單面板/雙面板,3.2 單面板雙層作法,3.3 浮雕線路,3.4,多層線路,目 錄,Product Introduction,Advantage,體積小,Small Size,重量輕,Light Weight,可折疊做,3,D,立體安裝,Flex-for-Installation,可做動態撓屈,Dynamic Flexibility,Application,Note-Book,Digital Camera,DVD/CD-ROM,HDD,Printer,Scanner,PDA,Cellular Phone,LCD,Auto-Mobile,Application For Nootbook,Hinge Cable,Double-sided FPC,Impedance 50,5,60,000 Cycles Flexure Life,EMI Strategy Application,Hinge Cable,Double-sided FPC,Impedance 50,5,60,000 Cycles Flexure Life,Cardbus,Double-sided FPC,100 MHz Transfer Speed,Touch Pad,Double-sided FPC,SMT Mounting,Application For Nootbook CD/DVD ROM,Double-sided FPC,Standard IDE Interface,Grounding Strategy Application,Single-sided FPC,Spindle Control Unit,Switch&Photo Sensor Applied on FPC,Single-sided FPC,60,000 Cycles Flexure Life,Ultra Thin Material Design,Application For Lcd Panel,LCM Cable,Double-sided FPC,SMC Mounting,EMI Noise Depression,LCM Cable,Double-sided FPC,SMC Mounting,ACF Laminating on FPC,LCM Cable,Double-sided FPC,Fine Pattern(L/S=1.6/1.8 mil),ACF Laminating on FPC,HDD Cable,Double-sided FPC,Application For PDA,Switch Board,Double-sided FPC,SMT Mounting,Battery Board,Single-sided FPC,SMC Mounting,High Current-carriyng Capacity,Application For CELLULAR PHONE,Double-sided FPC,100,000 Cycles Flexure Life,ACF Laminating on FPC,Double-sided FPC,Battery,Raw Material-CCL,相關名詞:,C,opper,C,lad,L,aminates,(,銅薄基材,),Single-Sided(,單面銅薄基材,),Double-Sided(,雙面銅薄基材,),Copper Foil:,銅箔，銅皮,RA,銅:,壓延銅箔,輾壓,方式,。,ED,銅:,電解銅箔,電鍍,方式,(Electrodeposited),。,Polyimide,(PI)聚亞醯胺:,是一種由,Bismaleimide,與Aromatic,Diamine,所,共同聚合,而成的優良樹脂,杜邦,公司,將之,做成,片材，稱為,Katpon,。,Adhesive,Conductor,Dielectric Substrate,Adhesive,Conductor,Dielectric Substrate,Dielectric Substrate,Adhesive,Mylar,Adhesive,Kapton,Raw Material-CVL,用途,:1.,補強軟板,2.,提供零件所需承載強度,3.,補償軟板厚度,材質區分,:,PI/PET/FR4/SUS,結合方式,:,PSA:,感壓型,Thermal Set:,熱固型,Thermal Plastic:,熱塑型,Raw Material-STIFFENER,FR4,PET,PI,SUS,Raw Material-Adhesive,3M467,3M9460,tesa 60980,Sony T4000,用途:,便軟板粘著在其他物件上，,類似於雙面膠,吉盛3702,Manufacturing Process,Coverlay,Adhesive,Copper,Adhesive,Base Film,Adhesive,Copper,Adhesive,Coverlay,鑽孔,NC Drilling,雙面板,Double Sided,黑孔&,鍍銅,Black Hole&,Cu Plating,CVL,壓合,CVL Lamination,沖孔,Hole Punching,沖型,Blanking,電測/目檢,Elec.-test&,Visual Inspection,表面黏著/組裝,SMT&Assembly,壓膜/曝光,D/F Lamination,&Exposure,顯影/蝕刻/去膜,D.E.S.,單面板,Single,Sided,自動光學檢測,Automatic Optical,Inspection,假貼合,CVL Lay up,錫鉛電鍍/噴鍚,Sn/Pb Plating,or HAL,電測/目檢,Elec.-test&,Visual Inspection,印刷,Screen Printing,浮雕線路製造流程,1.純銅箔下料,3.純銅貼下CVL,4.壓合,烘烤,5.微蝕,6.壓乾膜,7.曝光,2.純銅箔鑽孔(貼CVL 對位孔),亮面,棕化面,上下開燈,膠溢流在機台上,轉印到下依片製品的銅面上造成殘膠,鍍不上錫.,使用 TPX 防止轉印,以進入紙面方向進行壓乾膜製程.,8.DES,9.上 Coverlay,10.壓合烘烤,12.鍍錫鉛,13.沖型,懸浮端,1.設計上非懸空不可,2.較粗手指端,即使單雙跳線也要留 1mm 以上.,加強片不可切齊CVL開口.要留1mm 以上.,銅材粗化面結合 CVL 較牢靠.,加強片切齊 CVL 開口.易壓斷銅材,NG,1.處理掉棕化表面,避免噴錫製程,11.微蝕,The End,此课件下载可自行编辑修改，供参考！,感谢您的支持，我们努力做得更好！,17,