建模流程梳理2070706.ppt

Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,Click to edit Master title style,Click to edit Master text styles,Second level,Third level,Fourth level,Fifth level,*,*,卓达装配式项目建模原则,项目流程,涉及软件,软件,主要功能,Revit,模型创建、工程量统计、图纸导出,Navisworks,视点查看、碰撞检查、施工模拟,EBIM,多方查看模型、问题沟通、协同工作,模块种类,模块拆分编号,楼板：同一楼层模块尺寸、洞口尺寸一致，编号一致；不同楼层模块尺寸、洞口尺寸一致，序号一致，同时区分楼层。,外墙：一层和屋顶单独编号，中间层（层高一致）统一编号。,内墙：一层单独编号，中间层（层高一致）统一编号。,计划拆分编号：,实际拆分编号：,楼板拆分与计划一致，外墙和内墙几乎每个墙体一个模块（机电影响）。,5,模块拆分编码说明,YB(样板房),6,7,8,构件命名,-,结构,原则：依据构件类型特征简洁命名,建模过程中,9,楼板模块：,组成,：,18,厚,OSB,板,+203,龙骨,+8,厚,OSB,板,图纸,：龙骨排布平面图、剖面图、,18,厚,OSB,板布置图、,8,厚,OSB,板布置图、材料表,建模原则,10,楼板模块：,建模原则,1.,楼板模块四个方向的安装缝为,2mm,；,2.,楼板模块的龙骨间距,400mm,；,3.,与次梁垂直的方向，在碰到钢梁的地方都要加上垂直的短龙骨，这些短龙骨与楼板模块一起做；,4.,楼板模块的长度达到,7m,或是,8m,多时需分为两个模块；,11,外墙模块：,组成,：内部机电管线,+89,龙骨,+12,厚,OSB,板,+30,厚保温板,+12,厚卓达装饰板,图纸,：墙体平面图、龙骨排布立面图、,12,厚装饰板布置图、机电管线布置图、材料表,建模原则,12,外墙模块：,建模原则,1.,外墙水平拼接无缝隙；,2.,外墙龙骨层内侧做法需现场做；,3.,外墙模块,7m,或是,8m,多长的分为两个模块；,4.,外墙模块龙骨间距,600mm,，不需要加水平拉条；,5.,外墙模块顶部遇到多根悬臂梁：外墙模块不需要拆开，模块出图不变，龙骨布置现场做。,13,内墙模块：,组成：,12,厚,OSB,板,+89,龙骨,+,内部机电管线,+12,厚,OSB,板,图纸：墙体平面图、龙骨排布立面图、,12,厚,OSB,板布置图、机电管线布置图、材料表,建模原则,14,内墙模块：,建模原则,1.,内墙底部直接安装在楼板,OSB,上（底部不考虑安装缝问题），上侧距离钢梁底部,20mm,的安装缝；,2.,内墙水平两端与钢柱或是墙连接时，,不考虑,安装缝；,3.,内墙的长度可以达到,7m,或是,8m,多（一个柱间）；,4.,内墙模块顶部中间不开洞，所以顶部碰到钢梁要分块；,5.,内墙只做龙骨层，其他做法现场做；,6.,内墙龙骨间距,600mm,，不需要设水平拉条。,15,楼梯模块：,组成：槽钢,+56,厚花纹钢板,+18,厚,OSB,板,图纸：构件平面布置图、模块剖面图、材料表,建模原则,16,门窗洞口,建模原则,1.,门窗洞口跨度,3m,时，洞口两侧分别是两根,140 x41x12x2.5,的对抱龙骨，过梁做法如下图；,2.,洞口跨度大于,3m,时，洞口中间需要加设立柱，具体加设立柱做法以及相应门窗的调整需要设计院协助提供设计图纸。,17,建模原则,Than,k,s,！,18,