HZT365878PL1-01 3 8V 2500mAh(T1).pdf

16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -1-AP PPROVAL SHEET 产品承认书产品承认书 Customer 客户名称客户名称：德赛电子德赛电子（惠州惠州）有限公司有限公司 Part No 产品产品型号型号：HZT365878PL11-01(T1)Description 产品描述产品描述：3.8V 2500mAh Application 应用机型应用机型:SIGNATURE 制作方签名制作方签名 MADE BY 制作制作：李明英 DATE日期日期：2014-07-07 APPROVED BY 批准批准：严怀军严怀军 DATE日期日期：2014-07-07 CUSTOMER APPROVAL 客户确认客户确认 CONFIGURATION结构确认结构确认：DATE日期日期：FUNCTION 性能确认性能确认：DATE日期日期：APPROVED BY 批批 准准：DATE日期日期：16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -2-Amendment Record 修正记录修正记录 Revision 修订编号 Description 修订内容 Version版别 Date 日期 Approval 审核 1 新发行Initial Release A/1 2014-7-7 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -3-产产 品品 目目 录录 01Scope 适用范围适用范围 4 02Type 电池型号电池型号.4 03General Performance 常规性能常规性能 4 04Testing Item and Methods 性能性能及及测试方法测试方法.5 05PCM Characteristic 保护板性能保护板性能.6 06Environment Performance 环境环境适应适应性能性能 .7 07Safety Test 安全测试安全测试 .8 08Test Conditions 测试条件测试条件 .9 09Cautions In Use 使用警告使用警告 .9 10Battery Operation Instruction 电池操作说明电池操作说明.10 11Period Of Warranty 保质期保质期 11 12Other The Chemical Reaction 其它化学反应其它化学反应 .12 13Note 备注备注.12 附图附图 1：PCM Working Principle 保护板工作原理图保护板工作原理图 13 附图附图 2：Dimension 电池尺寸图电池尺寸图.14 附图附图 3：Battery Photo 电池电池照片照片 15 附录附录 1：ttachment 1 样品检测报告样品检测报告 16 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -4-1Scope 适用范围适用范围：1.1 This product specification applies to the lithium ion battery of Shenzhen Hi-Chipcom Electronics Co.,LTD.本产品规格书适用于海芝通电子（深圳）有限公司生产的锂离子成品电池 1.2 The products are based on standards:PRC national standards GB/T 18287-2013(cellular phone use lithium ion batteries general norm)and PRC national standards GB4943-2001(IT technology equipment safety standards).本产品基于国标 GB/T18287-2013 和 GB4943-2001 1.3 Please contact Hi-Chipcom coordination with the settlement if you have any questions.如果有什么问题请与海芝通联系 2Type 电池型号电池型号 2.01 Battery Type 电池型号：HZT365878PL11-01 (T1)2.02 Cell Type 电芯型号：365878PL 3.8V 2500mAh 3General Performance 常规性能常规性能 Item 项目项目 Specifications 性能性能 Remark 备注备注 3.01 Rated Capacity 额定容量 2500mAh(高容、高压)0.2C5A charge and discharge system 0.2C5A 充放制式 3.02 Min Capacity 最小容量 2450mAh(高容、高压)3.03 Nominal Voltage 额定电压 3.8V 3.04 Under discharge voltage 放电截止电压 2.75V 3.05 Charge method（Std.）充电方式（标准）CC/CV(恒流恒压)045 3.06 Charging Current 充电电流(Std.)（标准）(MAX)最大 0.2C5A 2A 3.07 Charging Voltage（Std.）充电电压（标准）4.35V 3.08Discharge 放电电流（Std.）标准 (MAX)最大 0.2C5A-10+50 2A 3.09 Impedance 内阻 180m AC Impedance 1kHz 交流阻抗值 1kHz 3.10 Weight 重量/大约 3.11 Max size 最大外形尺寸 4.4*60.2*83.2mm See the attached figure 2 见附图 2 3.12 Environment temperature:环 境 温 度:standard charge 标准充电 standard discharge 标准放电 0+50 -10+45 3.13 Storage temperature 存储温度-5+35 45%75%3.14 Voltage of shipment 出货电压 3.803.95V 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -5-4 Test Method And Standard 性能及性能及测试方法测试方法 4.1 Quick Charge Method 快速充电制式 The Quick Charge means charging the Cell at a constant current of 1C5A until the voltage is 4.2V,then charged at a constant voltage of 4.2V until its current is less than0.01C5A.“快速充电”即在环境温度为 205的条件下,先以恒定电流 1C5A 充电至 4.2V,再以 4.2V 的恒压充电至电流小于 0.01C5A.4.2 Standard Charge Method 标准充电制式 The Standard Charge means charging the Cell at a constant current of 0.2C5A until the voltage is 4.2V,then charged at a constant voltage of 4.2V until its current is less than 0.01C5A标准充电”即在环境温度为 205的条件下,先以恒定电流 0.2C5A 充电至 4.2V,再以 4.2V 的恒压充电至电流小于 0.01C5A.4.3 Capacity 容量 Battery lay aside 1 hour after standard charging,under the temperature 205,discharge by 0.2C5A with CC to terminal voltage to 2.75V 标准充电后，搁置 1h，在环境温度为(205)条件下,以 0.2C5A 电流恒流放电到 2.75V。300min Battery lay aside 1 hour after quick charging,under the temperature 205,discharge by 1C5A with CC to terminal voltage to 2.75V 快速充电后，搁置 1h，在环境温度为(205)条件下,以 1C5A 电流恒流放电到 2.75V.60min 4.4 Cycle Life 循环寿命 A cell is charged in accordance with 4.1,and stored for 0.5h1h,then discharged to the end-off voltage with the current of 1C5A,after that,stored 0.5h 1h prior to next charge-discharge cycle.The cell shall be continuously charged and discharged for 300 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -6-times.电芯按 4.1 规定充电,而后搁置 0.51h,然后以1C5A 电流放电至终止电压,放电结束后,搁置0.51h,再进行下一次充放电循环,连续进行充放电循环 300 次.4.5 Temperature Performance 温度特性 4.5.1 High Temperature Performance 高温放电特性 A cell is charged in accordance with 4.1 or 4.2,and stored in an ambient temperature of 552 for 2h,then discharged to cut-off voltage at a constant current of 1C5A.After that,fetch out the cell and place it in the ambient temperature of 205 for 2h,then check its appearance.电芯按 4.1 或 4.2 规定充电结束后,将电芯放入 552的高温箱中恒温 2h,然后以 1C5A 电流放电至终止电压,实验结束后,将电芯取出在环境温度为 205的条件下搁置 2h,然后目测电芯外观 1.the discharging time is not less than 51min;放电时间不低于51min;2.No distortion,no leakage no explosion.电芯外观无变形、漏液、爆裂.4.5.2 Low Temperature Performance 低温放电性能 A cell is charged in accordance with 4.1 or 4.2,and stored in an ambient temperature of-202 for 16h24h,then discharged to cut-off voltage at a constant current of 0.2C5A.After that,fetch out the cell and place it in the ambient temperature of 205 for 2h.电芯按 4.1 或 4.2 规定充电结束后,将电芯放入-202的低温箱中恒温 1624h,然后以 0.2C5A 电流放电至终止电压,实验结束后,将电芯取出在环境温度为205的条件下搁置 2h。1.The discharging time is not less than 3h;放电时间不低于 3h;2.No distortion,no leakage no explosion.电芯外观无变形、漏液、爆裂.4.6 Charge(Capacity)Retention 荷电保持能力 A cell is charged in accordance with 4.2 or 4.3,and stored in an ambient temperature of 205 for 28d,then discharged to cut-off voltage at a constant current of 0.2C5A.电芯按 4.1 或 4.2 规定充电结束后,在环境温度为205条件下,将电芯搁置 28 天,再以 0.2C5A 电流放电至终止电压.Retention:85%C5A 容量保持率:85%C5A 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -7-5 PCM Characteristic 保护板性能保护板性能 Item 项 目 Min 最小值 Type 典型值 Max 最大值 note 备 注 5.01 Overcharge protection voltage 过充保护电压 4.350V 4.375V 4.4V adjustable 可调 5.02 Overcharge protection delay time 过充保护延时时间 0.08S 0.2S 5.03 Overcharge protection recovery voltage 过充保护恢复电压 4.170V 4.175V 4.180V adjustable 可调 5.04 Discharge protection voltage 过放保护电压 2.437V 2.5V 2.563V adjustable 可调 5.05 Discharge protection delay time 过放保护延时时间 20 mS /5.06 Over current protection current 过流保护电流 2.0 5.0A 5.07 Over current protection test voltage 过流检测电压 0.12V 0.1V 0.15V adjustable 可调 5.08 Over current protection delay time 过流保护延时时间 10 mS 5.09 Short circuit test voltage 短路检测电压 VDD-1.2V VDD-0.9V VDD-0.6V Between VM and VDD VM 与 VDD 之间 5.10 Short circuit protection time 短路保护延时时间 230uS 500uS 5.11 Working consumption current 工作电流消耗 1.0A 7.0 5.12Static current consumption 静态电流消耗 3A 4A 5A 5.13 Static current protection 静电(ESD)保护-10KV-+10KV The protection unit work well 各项保护功能正常 5.14 Impedance 内阻(500mAh)RSS65m 6 Environment Characteristic 环境环境适适应应性能性能 项 目 测 试 方 法 判 定 标 准 6.1 Constant Temperature and Humidity 恒定湿热性能 A cell is charged in accordance with 4.1 or 4.2,and stored in an ambient temperature of 402(9095%RH)for 48h,then placed in room temperature for 2h.After that,check its appearance prior to being discharged to cut-off voltage at a constant current of 1C5A.电芯按 4.1 或 4.2 规定充电结束后,将电芯放入 402(901.no distortion,no rust,no fume,no explosion;电芯外观应无变形,锈 蚀,冒烟或爆炸;2.the discharging time is not less than 36min.16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -8-95%RH)的恒温恒湿箱中搁置 48h 后,将电芯取出在室温下搁置 2h,目测电芯外观,再以 1C5A 电流放电至终止电压 放电时间应不低于 36min.6.2 Vibration Test 振动测试 A cell is charged in accordance with 4.1 or 4.2,then installed onto the vibration desk with clamps.Equipment parameters of frequency and amplitude are as follows(the frequency is to be varied at the rate of 1oct/min between 10 and 55 hertz,and repeat vibration for 30min.The cell is to be tested in three mutually perpendicular directions):frequency:10Hz30Hz amplitude:0.38mm frequency:30Hz55Hz amplitude:0.19mm check the appearance of the cell and test the voltage 电芯按4.1或4.2的规定充电结束后,将电芯用夹具安装在振动台的台面上，按下面的振动频率和对应的振幅调整好实验设备.X,Y,Z 三个方向每个方向上从 1055Hz 循环扫频振动 30min，扫频速率为1oct/min:振动频率：10Hz30Hz 位移幅值(单振幅)：0.38mm;振动频率：30Hz55Hz 位移幅值(单振幅)：0.19mm.振动结束后,观察电池外观，检测电池电压。1.no scratch,no leakage,no fume,no explosion;电芯外观应无明显损 伤，漏液，冒烟或爆炸；2.the voltage is min3.8V.电芯电压不低于 3.8V.6.3 Shock Test 碰撞测试 A cell is tested in accordance with 6.2,then secured to the testing machine by means of rigid mount which supports all mounting surfaces of the cell.Each cell shall be subjected to a total of three shocks of equal magnitude.The shocks are to be applied in each of three mutually perpendicular directions.The acceleration and impulse time are as follows:acceleration of impulse peak value:100m/s2,shock frequency:4080times/min,impulse lasting time:16min,shock times:100010 电池按6.2的规定试验结束后,将电池分别按X,Y,Z三个互相垂直轴通过夹具坚固在台面上,按下述要求调好加速度,脉冲持续时间进行碰撞实验:脉冲峰值加速度100m/s2,每 min 碰撞次数:4080,脉冲持续时间:16ms,碰撞次数：100010.1.no scratch,no leakage,no fume,no explosion;电芯外观应无明显损 伤，漏液，冒烟或爆炸；2.the voltage is Min n*3.8V.电芯电压不低于 n*3.8V.6.4 Drop test 自由跌落 A cell is charged in accordance with 6.3,then dropped from a height of 1000mm to a wooden board(18-20mm thick)which is placed on the concrete ground.Cells shall be dropped in each of three mutually perpendicular directions.Total drop times are 6.After that,the cell is discharged to cut-off voltage at CC of 1C5A,then repeat charge&discharge at a current of1C5A until the discharge time is not less than 51min,the cycle times should be not more than 3.电池按 6.3 的规定试验结束后,将电芯样品由高度为 1000mm 的位置自由跌落到置于水泥地面上的 18-20mm 厚的木板上，从 X,Y,Z正负方向(六个方向)每个方向自由跌落 1 次.自由跌落结束后,将电池以1C5A电流放电至终止电压,然后以1C5A的电流进行充放电循环,直至放电时间不低于 51min,即可终止充放电循环,1charge and discharge cycle are on more than 3 times.充放电循环次数应不多于 3次.2 no leakage,no fume,no explosion.电芯应不漏液，冒烟或爆炸 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -9-7.Safety Test 安全测试安全测试 All below tests are carried out on the equipments with forced ventilation and explosion-proof device.Before test,all cells are charged in accordance with 4.1 or 4.2,and stored 24h prior to testing.下述试验应在有强制排风条件及防爆措施的装置内进行,在试验前所有的电池都按 4.1 或 4.2 规定充电,并搁置 24h 后,再进行以下试验.Test Item 测试项目 Test Method 测试方法 Criteria 检验标准 7.1 Impact Test 重物冲击 A cell is to be placed on the impact flat.A 10 kg weight is to be dropped from a height of 1m onto the cell.将电池放在冲击台上,将 10kg 重锤自 1m 高度自由落下,冲击电芯。With no fire,no explosion 不起火,不爆炸 7.2 Heating Test 热冲击 A cell is to be heated in a circulating air oven.The temperature of the oven is to be raised at a rate of 52 per minute to a temperature of 1302 and remain for30min at that temperature before the test is discontinued.将电芯放在电热鼓风干燥箱中,温度以 52/min的速率由室温升至 1302并保持 30min.no fire,no explosion 电芯不起火,不爆炸 7.3 overcharge test 过充电 A cell is to be subjected to CC/CV power by connecting its positive&negative terminal,then set the current as 1C5A,the voltage as 5.0V,after that,Charge the cell up to 5.0V at CC of1C5A and last 2h at the voltage of 5.0V.将电芯正负极连接于恒压电源,调节电流至 1C5A,电压为5.0V,然后对电芯以1C5A充电,直到电压为5.0V,并恒压保持2h.no fire,no explosion 电芯不起火,不爆炸 7.4 Over discharge testing 过放测试 At 235,According to the requirements of standard charge,the battery will be discharge to cut-off voltage,then connect with external load of 30 ohm for 24 hours.在 235状态下,按标准放电的要求放电至终止电压后,外接 30 负载放电 24 小时.No fire,no smoke,no leakage.无起火,无冒烟,无泄液 7.5 Short-circuit test 短路测试 A Cell is to be short-circuited by connecting the positive and negative terminals of the cell with copper wire having a maximum resistance load of 50m?.Monitor its temperature while testing,the cell is to be discharged until the cell case temperature has returned to be 10 less then peak temperature.将接有热电偶的电芯置于通风橱中,用铜线短路其正负极(线路总电阻不大于50毫欧),实验过程中监视电芯温度变化,当电芯温度下降到比峰值低约 10时,结束实验.no fire,no explosion 电芯不起火,不爆炸 16海芝通电子(深圳)有限公司 HI-CHIPCOM ELECTRONIC(SHENZHEN)CO,.LTD 深圳市宝安区福永镇塘尾福民工业区 B2 栋 TEL:[phone]/8168 FAX:[phone] www.hi-Email:Jessicahi-NO.编号编号 HZT365878PL11-01 (T1)DESCRIPTION 描述描述 3.8V 2500mAh Lithium Polymer Rechargeable Battery 3.8V 2500mAh 可充电聚合物电池 DATE 日期日期 2014-7-7 Version 版别 A/1 -10-8Testing conditions 测试条件测试条件 8.1 Circumstance 测试环境条件 Unless otherwise specified,all tests stated in this product specifications Should be conducted under the following atmosphere conditions:除非另有规定，本规格书中各项试验应在标准大气条件下进行：Temperature:1535 温度：1535 Relative humidity:4575%相对湿度：45%75%Atmospheric pressure:86kpa106kpa 大气压力：86kPa106kPa 9.CAUTIONS IN USE 使用警告使用警告 9.1 To ensure proper use of the battery please read the manual carefully before using it.Handling 为了使电池安全的使用及处理请在使用前认真的阅读操作说明 Do not expose to,dispose of the battery in fire.不能把电池曝晒或丢在火中 Do not put the battery in a charger or equipment with wrong terminals connected.电池充电时不能把正负极性装反 Avoid shorting the battery 避免短路电池 Avoid excessive physical shock or vibration.避免过分的物理震动和冲击电池 Do not disassemble or deform the battery.不能拆解或使电池变形 Do not immerse in water.不能将电池浸入水中 Do not use the battery mixed with other different make,type,or model batteries.不能将其它不同厂家，类型，型号的电池混合使用 Keep out of the reach of children.禁止小孩接触电池 9.2 charge and discharge 充放电 Battery must be charged in appropriate charger only.电池必须在合适的条件下充电 Never use a modified or damaged c