DIP零件认识.ppt

按一下以編輯母片標題樣式,按一下以編輯母片,第二層,第三層,第四層,第五層,*,DIP,零件認識,DIP Components Introduction,AGP SLOT(AGP,顯示卡插槽),AGP SLOT(AGP,顯示卡插槽),1.外觀特徵,Visual Features：,(1),零件上方有標示零件廠牌。,The body shows the vender brand.,(2),有方向,方向以零件三支防呆固定腳為插件方向。,The three fixed pins lead to the correct insertion direction,.,(3),在,PC,板上之插件位置標示,AGP,Marked on board with AGP.,2.,插件說明及注意事項,Notice:,(1),零件識別卡：插件位置和零件腳腳數,The label showing the number of pins and location on PCB,(2),插件難度:低度控制,The degree of insertion is low control,(3),其他:無,O,ther:,Box Header(,傳輸控制連接埠),防呆,缺口,gap,Box Header(,傳輸控制連接埠),1.外觀特徵,Visual Features：,(1),零件側方有標示零件廠牌或腳數。,The body shows the vender brand or the numbers of pins.,(2),有方向時,方向以零件上的排針缺腳數為定義防呆方向。,The fixed pin lead to the correct insertion direction on its,.,(3),在,PC,板上之插件依位置名稱標示 如：,FLOPPY/IDE1,Marked on board with each location,eg,.:FLOPPY/IDE1,2.,插件說明及注意事項,Notice:,(1),零件識別卡：插件位置名稱及標示第一支腳的方向,The label showing the location and first pin side for insertion.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:無防呆腳時以側面缺口方向指示插件,Other:Directing by the specific gap while without key-pin.,Battery Holder(,電池座),Battery Holder(,電池座),1.外觀特徵,Visual Features：,(1),零件上的電池座壓條有電性正向(+)標示。,The top side shows the positive mark on(+).,(2),有方向,方向以機板上圖面所示電池形狀定義。,The shape drawing on the board superposition to the comp.,(3),在,PC,板上之插件依位置名稱標示 如：,BT1,Marked on board with each location,eg,:BT1,2.,插件說明及注意事項,Notice:,(1),零件識別卡：板上插件位置。,The label showing the location on PCB.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:零件未加防呆腳,插件時需注意方向標示,Other:Pay attention to the component without the leading pin.,Battery(,電池),Battery(,電池),1.外觀特徵,Visual Features：,(1),正面有雷射標示電池廠牌,尺寸,及電壓數。,The top side shows the brand,size and volts of the battery.,(2),有方向性,裝置於電池座上時,字面朝上。,The setting direction should shows on the top side.,(3),在,PC,板上之插件位置標示,BT1,Marked on board with BT 1,2.,插件說明及注意事項,Notice:,(1),零件標示卡：無,None,(2),插件難度：無,None,(2),其他：無,None,DIMM(,記憶體插槽),DIMM(,記憶體插槽),1.外觀特徵,Visual Features：,(1),零件上方有標示零件廠牌及電壓數值。,The body shows the vender brand and the volts value.,(2),有方向,方向以零件三組防呆固定架為插件方向。,The three fixed pins lead to the correct insertion direction,.,(3),在,PC,板上之插件位置標示,DIMMxx,如：,DIMM1,Marked on board with,DIMMxx,eg,:DIMM1,2.,插件說明及注意事項,Notice:,(1),零件標示卡：插件位置相對零件腳腳數,The label showing the number of the pin and location on PCB.,(2),插件難度:中度控制,The degree of insertion is middle control.,(3),其他:插件時易折腳類零件,Pin-bent easily while insertion.,SLOT(ISA Slot&SLOT 1),ISA Slot,Slot 1,SLOT(ISA Slot&SLOT 1),1.外觀特徵,Features：,(1),零件上方有標示零件廠牌。,The body shows the vender brand.,(2),有方向,方向以零件腳設計插件方向防呆。,The Fool-Proof pins lead to the correct insertion direction,.,(3),在,PC,板上之插件位置標示,Slot 1,或,ISA 1,Marked on board with Slot 1II or ISA 1.,2.,插件說明及注意事項,Notice:,(1),零件標示卡:無,The label showing the number of the pin and location on PCB.,(2),插件難度:高度控制,The degree of insertion is high control,(3),其他:是,kink,腳零件插件時加壓防止零件浮件,Because of the kink-pin,pressing for not floating while inserting.,HEADER(,排針),HEADER(,排針),1.外觀特徵,Features：,(1),零件腳較短的一側為插件孔方向。,The shorter pins is the side for insertion.,(2),有方向時,方向以零件上的排針缺腳數為定義防呆方向。,The fixed pin lead to the correct insertion direction on its,.,(3),在,PC,板上之插件依位置名稱標示 如：,JP3,Marked on board with each location et:JP3,2.,插件說明及注意事項,Notice:,(1),板上插件標示:板上插件位置名稱及標示第一支腳的方向,The label showing the location name and first pin side for insertion.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:加上,JUMPER,時,於插件時需調整為高度控制零件,Exchange the degree to high control while with jumpers on.,WAFER HD(,訊號連接端),防呆,Pin,Extra Pin,WAFER HD(,訊號連接端),WAFER HD(,訊號連接端),1.外觀特徵,Features：,(1),零件腳較短的一側為插件孔方向。,The shorter pins is the side for insertion.,(2),有方向,方向以零件上的防呆固定腳數為定義方向。,The extra fixed pin lead to the correct insertion direction on its,.,(3),在,PC,板上之插件依位置名稱標示 如：,CPU_FAN,Marked on board with each location et:CPU_FAN,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱及防呆腳的方向,Showing the location name and the extra for insertion.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:部份零件未加防呆腳時,插件時需注意方向標示,Pay attention to some brand whose parts without the extra pin.,SLOT(,介面卡插槽-,PCI,規格),SLOT(,介面卡插槽-,PCI,規格),1.外觀特徵,Features：,(1),零件上方有標示零件廠牌。,The body shows the vender brand.,(2),有方向,方向以零件二支防呆固定腳為插件方向。,The two fixed pins lead to the correct insertion direction,(3),在,PC,板上之插件位置標示,PCIxx,如:,PCI1/PCI2,Marked on board with,PCIxx,et:PCI1/SLOT2,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:無,None,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:是,kink,腳零件插件時加壓防止零件浮件,Because of the kink-pin,pressing for not floating while inserting.,IC SOCKEK(IC,腳座),缺口位置,IC SOCKEK(IC,腳座),1.外觀特徵,Features：,(1),零件上方有標示零件廠牌及電壓數值。,The body shows the vender brand and the volts value.,(2),有方向,方向以零件上的缺口方向為區別式。,The three fixed pins lead to the correct insertion direction,.,(3),在,PC,板上之插件位置標示,Uxx,如：,U20/U21,Marked on board with,Uxx,et:U20/U21,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置三角缺口與零件上缺口相對,Showing the triangle of the side to the parts on board.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:插件時易折腳類零件,Pin-bent easily while insertion,XTAL(,振,盪器),XTAL(,振,盪器),1.外觀特徵,Features：,(1),跪腳式(筒狀)外觀無頻率數值標示,臥式振盪器零件上方有雷射,標示頻率數值。,The body of the bowl shape without showing the spec value of,frequency,but the lying shape shows on its top side.,(2),無極性,無方向性。,Without polarity and direction,.,2.,在,PC,板上之插件位置標示,Yxx,如：,Y1/Y2,Marked on board with,Yxx,et:Y1/Y2,二、插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:無,None,(2),插件難度:高度控制,The degree of insertion is high control,(3),其他:加工預減零件腳,Pre-cut the pin before insertion,Diode(,二極體),+,Diode(,二極體),1.外觀特徵,Features：,(1),外表本體部份有標示機構尺寸;1,N5817,表示板上之兩腳距,10,mm,1N5820,為板上兩腳距20,mm。,The body of the diodes shows the pitch:the 1N5817 means the,pitch 10mm,1N5820 means the pitch 20mm.,(2),有極性,零件本體外有一圈銀色環帶表示正極方向。,The positive is showed on the body as a silver round circle.,.,(3),在,PC,板上之插件位置標示,Dxx,如：,D1/D2,Marked on board with,Dxx,et:D1/D2,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:箭頭方向表正極,The arrow means positive,(2),插件難度:高度控制,The degree of insertion is high control,(3),其他:加工預減零件腳/整腳,Pre-cut the pin before insertion,ATX Power Conn.(,電源插座),ATX Power Conn.(,電源插座),1.外觀特徵,Features：,(1)ATX,零件為排盒狀,端子為內藏式;一般電源插座端子為外露式,The ATX Power is the box shape and pins inside it;the power,connector pins were outside and,isn,t the box shape,.,(2),有方向,方向以零件兩組防呆固定架為插件方向。,The two fixed pins lead to the correct insertion direction,.,(3),在,PC,板上之插件依位置名稱標示 如：,ATXPWR,Power Conn.,Marked on board with each location et:ATXPWR,Power Conn.,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱,Showing the location name and first pin side for insertion2),插件難度:高度控制,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting.,CPU SCK(,中央處理器腳座),CPU SCK(,中央處理器腳座),1.外觀特徵,Features：,(1),零件上方有標示零件廠牌及零件腳座腳數。,It shows the vender brand and the number of the pins on it.,(2),有方向,方向以零件腳設計插件方向防呆。,The Fool-Proof pins lead to the correct insertion direction,.,(3),在,PC,板上之插件位置標示,Uxx,如:,U5/U10,Marked on board with,Uxx,et U5/U10,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:標示位置有,SOCKET,字樣於腳座旁,Shows“SOCKET“by the side of the CPU Socket.,(2),插件難度:低度控制,The degree of insertion is low control.,(3),其他:,無,None,Inductor(,線圈電感),Inductor(,線圈電感),1.外觀特徵,Features：,(1),外裝陶磁瓷依各廠商有所不同。現廠內使用廠牌1.0,UH、,1.2UH,及2.5,UH,為綠/藍色，10,UH,及20,UH,為黃/白色。,By each vendors,colored with different outside wearing;et:the,4UH and 7UH are green/blue,10UH and 20UH are yellow/white.,(2),無極性,零件規格以陶瓷本體及線圈線徑,線圈數決定。,The spec of the inductor is measured base on the body,the dime.,of the wire and the numbers of turn.,.,(3),在,PC,板上之插件位置標示,Lxx,如：,L12,Marked on board with,Lxx,et:L12,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:零件規格值,The UH spec of components,(2),插件難度:中度控制,The degree of insertion is middle control,(3),其他:加工預減零件腳,Pre-cut the pin before insertion,MINI DIN(PS/2,鍵盤/滑鼠插座),MINI DIN(PS/2,鍵盤/滑鼠插座),1.外觀特徵,Features：,(1),零件分為有無彈片兩種(上為有彈片)。,The parts class to shield type or not.(Above with shield type),(2),有方向,五組防呆固定腳及零件腳呈不對稱排列。,The five kinks and asymmetry pins lead to the correct insertion,.,(3),在,PC,板上之插件依位置名稱標示 如：,Keyboard/Mouse,Marked on board with each location et:,Keyboard/Mouse,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱,Showing the location name for insertion.,(2),插件難度:高度控制,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting.,Printer Port(,印表機插座),Printer Port(,印表機插座),1.外觀特徵,Features：,(1),有兩顆六角螺絲,零件上方標示零件廠牌及腳位編號。,With two screws and shows the brand and the pin number on.,(2),有方向,兩組防呆固定腳及零件腳呈不對稱排列。,The two kinks and asymmetry pins lead to the correct insertion,.,(3),在,PC,板上之插件依位置名稱標示 如：,PRINTER,Marked on board with each location et:PRINTER,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱及零件腳數目,Showing the location name and the pin#for insertion.,(2),插件難度:高度控制,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting,.,USB(,通用序列匯流排),USB(,通用序列匯流排),1.外觀特徵,Features：,(1),零件分為有無彈片兩種(上為有彈片)。,The parts class to shield type or not.(Above with shield type),(2),有方向,兩支防呆固定腳及零件腳呈不對稱排列。,The two kinks and asymmetry pins lead to the correct insertion,.,(3),在,PC,板上之插件依位置名稱標示 如：,KB,Marked on board with each location et:KB,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱,Showing the location name for insertion.,(2),插件難度:高度控制,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting.,Game/Audio Port(,搖桿/聲音插座),1.外觀特徵,Features：,(1),有兩顆六角螺絲,零件上方標示零件廠牌及腳位編號。,With two screws and shows the brand and the pin number on.,(2),有方向,兩組防呆固定腳及零件腳呈不對稱排列。,The two kinks and asymmetry pins lead to the correct insertion,.,(3),在,PC,板上之插件依位置名稱標示 如：,Mic,-In Line-In Line Out Game,Marked on board with each location et:,Mic,-In Line-In Line Out Game,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱。,Showing the location name.,(2),插件難度:高度控制。,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting,.,Game/Audio Port(,搖桿/聲音插座),VGA/COM(,顯示卡/串列埠插座),VGA/COM(,顯示卡/串列埠插座),1.外觀特徵,Features：,(1),有兩顆六角螺絲,零件上方標示零件廠牌及腳位編號。With two screws and shows the brand and the pin number on.,(2),有方向,兩組防呆固定腳及零件腳呈不對稱排列。,The two kinks and asymmetry pins lead to the correct insertion,.,(3),在,PC,板上之插件依位置名稱標示 如：,VGA,Com 1,Marked on board with each location et:VGA,COM 1,2.,插件說明及注意事項,Insertions Instruction：,(1),板上插件標示:板上插件位置名稱及零件腳數目,Showing the location name and the pin#for insertion.,(2),插件難度:高度控制,The degree of insertion is high control.,(3),其他:插件時如未加壓平貼板面過錫爐易浮件,Component floating easily while without pressing inserting,.,Capacitor(,電容),Capacitor(,電容),1.外觀特徵：,(1)外裝上標示廠牌及耐溫上限，封皮依各廠商有所不同。如三洋,電容顏色為綠色。,By each vendors,colored with different outside wearing(et:the,SANYO is green)and shows on the top temper spec.,(2),有極性,零件外裝封皮上有圓圈及顏色區域標示,表負極。,The negative is showed on the outside wearing with a circle,.,(3),在,PC,板上之插件位置標示,ECxx,/,ECxx,如：,EC2/EC3,Marked on board with,ECxx,/,ECxx,如：,EC2/EC3,2.,插件說明：,(1)板上插件標示:圓圈方向表負極,The circle means negative,(2),插件難度:高度控制,The degree of insertion is high control,(3),其他:加工預減零件腳,Pre-cut the pin before insertion,Buzzer(,蜂鳴器),Buzzer(,蜂鳴器),