模具设计DFM模板..ppt

单击此处编辑母版标题样式,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,*,*,FS0000F,DFM Report,DFM Engineer,：,LIMIN,Approved:,Date,：,2014/02/26,DFM Design For Manufacture,Five-Star Tooling Limited,Project name:,Mould No.,FS0000E,Customer,Name,UKAG,Customer,mould No.,请客人提供,Part No.,Screen Side Frame,Cavities,1+1,Material,PC/ABS BAYER T65XF,Size for 1 part,182.7X126.9X35,Inch/mm,mm,产品信息,Product Information,开 模 客 供 资料,information to be provided by customer,序,号,资料名称,Name,内 容,Description,收到日期,Received date,备注,remarks,1,胶 料,(resin),PC/ABS BAYER T65XF,2014.02.25,2,缩 水 率,(hrinkage),请客人提供,我们选定为,0.005，,请客人确认或提供,3,啤机吨位,(Press tonnage),请客人提供啤机的相关信息,4,设计标准,customer tooling standard,请客人提供,5,胶料特性,resin date sheet,请客人提供,开模时需要收到的客供资料,上下模分析,CAV/COR,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,cavity side,core side,进浇口建议,Gate Advice（,方案一,）,冷流道，两点潜水入胶,170mm,冷流道，潜水入胶。优点：不需热流道板。缺点：流道长，注塑压力大。,模具排位，模胚尺寸为,5565,进浇口建议,Gate Advice（,方案二,）,（,推荐,）,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,Moldmaster 1 open nozzle HRM,/Sub Gate,Hot Sprue,Sub Gate,由于产品较大，同时根据排位需要，我们建议客人每个产品用一个热转冷流道，两点潜水。,（请客人确认热嘴的型号并确认,是否需要订购接线盒，并提供具体品牌及型号，接线方式。）,同时，请客人确认另一个产品是否为完全镜像关系。请市场考虑增加热嘴报价。,热嘴转冷流道潜水入胶。优点：流道短，注塑压力小，产品填充好。缺点：需要热流道板，模具成本相应增加。,模具排位，模胚尺寸为,5565,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,结构分析,Structure analysis,Structure,Quantity,Slide,1,Lifter,0,Collapasible core,/,Core slider 01,C,C,C-C,见下页,Customer comment.please give your approval and comments),Date,Approval by:,Remark,OK or NG,结构分析,Structure analysis,Core side,ST1=8,ST2=20,8,SECTION C-C,自制定位零件，底部加弹弓,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,镶件分析,Insert analysis,Cavity Insert,做浮动镶件，避免产品粘前模,10,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,镶件分析,Insert analysis,Core Insert,下模三个镶件，每个镶件上下两支扁顶针,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,顶出建议,Eject Advice,Core side,顶针,EJECTOR PIN,STRAIGHT,BAR,STRIPPER,BAR,分型线分析,PL analysis,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,行位分型线需移到此处，与前模做,3,度的插穿角,分型线分析,PL analysis,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,此面插穿角不够，需修到,35,度,两处,一处,为了更好的封胶，此处的插穿距离尽可能修到,2.5MM,以上,分型线分析PL analysis,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,为简化加工及分型，指示处减胶,0.03MM，,出后模,擦穿位置分析,Shut off position,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,此面插穿角不够，需修到,3,度,擦穿位置分析,Shut off position,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,此面插穿角不够，需修到,3,度,产品出模分析,Product Draft analysis,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,Draft analysis,Draft OK,产品料厚分析,Product,Thickness analysis,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,产品胶料厚度均匀,产品光洁度标准,NO Texture,请提供光洁度标准,Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,1、,版本号我司做镶针，相关的字体我司默认为晒字，深,0.2MM，,凸字。,日期镶件（年月一起）,Engraving (O,thers),Customer comment.(please give your approval and comments),Date,Approval by:,Remark,OK or NG,模具排位,Mould overall dimensions,Mold overall layout,EJ SIDE PLAN VIEW,550,650,模胚已超报价（,4045,），请客人确认是否合适啤机，同时，市场考虑是否增加报价,22,备注,Remark,：,烦请贵司在我司提供的开模方案上每页做明确回复（同意或不同意），如未作明确回复的部分，我司将视为默认我司方案，我司将按此方案进行后续工作。,Please reply against our PPT in each page(OK or Nok),if there is,no,comment in any page of the PPT,we will consider it as“OK”and we will implement the proposal in the PPT,.,THANK,YOU!,