基于STM32的数据采集系统英文文献.doc

Design of the Data Acquisition System Based on STM32ABSTRACTEarly detection of failures in machinery equipments is one of the mostimportant concerns to industry。 In order tomonitor effective of rotating machinery, we development a micro-controller uC/OS-II system of signal acquisition system based on STM32 in this paper。 we have given the whole design scheme of system and the multichannel vibration signal in axis X， Y and Z of the rotary shaft can be acquired rapidly and display in realtime。 Our system has the character of simple structure, low power consumption, miniaturization.Keywords：STM32； data acquisition； embedded system;uC/OSII；1. 1。 IntroductionThe real-time acquisition of vibration in rotating machinery can effectively predict， assess and diagnose equipment operation state， the industry gets vibration data acquisition Rapidly and analysis in real-time can monitor the rotating machinery state and guarantee the safe running of the equipment。 In order to prevent failure， reduce maintenance time， improve the economic efficiency, The purpose of fault diagnosis system can detect these devices through the vibration signal acquisition of rotating machinery， and process the data acquisition, then it will make timely judgment of running state of equipment 。While the data acquisition module is the core part of the fault diagnosis system 14。The practical application in the industrial field， is the equipment operating parameters will be acquired to monitor equipment operating state。 In traditional data acquisition systems， the data from acquisition card are generally send into the computer， and specific software will be developed for the data acquisition. The main contribution of this paper has designed the STM32 platform with ARM technology, that has become a traditional mainstream technology in embedded systems， and the collecting data toward the direction of high realtime, multi-parameter, high-precision, while data storage become large capacity, more miniaturization and portable， and the development of multicommunication mode and long-distance for data transmission。 So as to meet the actual acquisition system multitasking requirements, this article has designed based on STM32 micro-controller uC/OSII system of signal acquisition system。 Therefore， in order to meet the actual acquisition system multitask requirements, this novelty of this article has designed a signal acquisition system in microcontroller uC/OSII based on STM32。2。Architecture of data acquisition systemData acquisition as key technology for monitoring equipment, recently a lot of work has been done on it. An embedded parallel data acquisition system based on FPGA is Optimized designed which will make it reasonable to divide and allocate high-speed and lowspeed A/D 5. Instead， it has use a highspeed A/Dconverter and Stratix II series of FPGA for data collection and processing， in which the main contribution is used of the Compact Peripheral Component Interconnect, the system has the characters of modularization， sturdiness and scalability 6.But remote control will be needed in Special Conditions， this paper introduce the embedded operating system platform based on Windows CE and uC/OS-II to design a remote acquisition and control system with the GPRS wireless technology 7-8.In order to achieve the data sharing of multiuser， it has build the embedded dynamic website for data acquisition management and dissemination with the ARM9 and Linux operation system 9.A data collection terminal devices is designed based on ARM7 microprocessor LPC2290 and embedded realtime operating system uC/OSII to solve the realtime acquisition of multichannel small signal and multi-channel transmission10.On the other hands， two parallel DSPbased system dedicated to the data acquisition on rotating machines， and the inner signal conditioner is used to adapt the sensor output to the input range of the acquisition, and then signal postprocessing by the design software， while the most frequently structure is to use DAS and FPGAbased， and such programs are also dependent on the DAS cost.In order to meet market requirements of low power consumption， low cost， and mobility, Fig.1 in this paper presents the design overall structure diagram of data acquisition system。 Through SPI interface， the system gets the data collection with three axis acceleration sensor into the STM32 controller of inner A/D conversion module with 12-bit, this process is non-interfering parallel acquisition。 Our system uses 240x400 LCD and touch screen module realtime to display the collected data in real time。2。1。 STM32 micro-controllerA 32 bit RISC STM32F103VET6， used as the processor in our system， compared with similar products, the STM32F103VET6 work at 72MHZ， with characters of strong performance and low power consumption, real-time and lowcost. The processor includes： 512K FLASH， 64K SRAM， and it will communicate by using five serial ports which contain a CAN bus， a USB2。0 SLAVE mode and a Ethernet interface, what s more two RS232 ports are also included。 The system in our paper extend the SST25VF016B serial memory through the SPI bus interface， that will regard as the temporary storage when collect large number of data， furthermore, we have the A/D converter with 12 bits resolution, and the fastest conversion up to 1us， with 3。6 V fullscale of the system。 In addition to design of the system power supply circuit， the reset circuit， RTC circuit and GPIO port to assurance system needs and normal operation。2.2. Data acquisitionThe machine state is normal or not is mainly depended on the vibration signal。 In this paper， to acquire the vibration data of rotating machinery rotor， we have used vibration acceleration transducers MMA7455L which could collect the data from axis x， y， and z of the company of Freescale. The kind of vibration acceleration transducers has advantage of low cost and small size， high sensitivity and large dynamic range with small interference。 MMA7455L is mainly consists of gravity sensing unit and signal conditioning circuit composition, and this sensor will amplify the tiny data before signal preprocessing。 In data acquisition process of our system， the error of sampling stage is mainly caused by quantified， and the error is depended on the bits of the A/D converter ，when we regard the maximum voltage as V max ， the AD converter bits is n， and the quantization Q = V max/2n， then， the quantization error is obeyed uniform distribution in q / 2， q / 2 13.The designed STM32 could built at most three 12bit parallel ADC in this paper ， which theoretical index is 72dB and the actual dynamic range is between 54 to 60dB while 2 or 3 bits is impacted by noise, the dynamic range of measurement can up to 1000 times with 60dB。 For the vast majority of the vibration signal， the maximum sampling rate of 10kHZ can meet actual demand, and the higher frequency of collection is generally used in the 812 bits AD， therefore one of contribution of this work is to choose a builtin 12-bit A/D to meet the accuracy of vibration signal acquisition and lower cost in this experiment。3.Software design3。1。 Transplantation of C/OSIn order to ensure real-time and safety data collection requirements, in this system， a kind of RTOS whose source code is open and small is proposed. It also can be easily to be cut down， repotted and solidified， and its basic functions including task management and resource management, storage management and system management。 The RTOS embedded system could support 64 tasks, with at most 56 user tasks， and four tasks of the highest and the lowest priorities will be retained in system. The uC/OS-II assigns priorities of the tasks according to their importance， the operation system executive the task from the priority sequence and each task have independent priority。 The operating system kernel is streamlined, and multi-tasking function is well compared with others， it can be transplanted to processors that from 8-bit to 64bit。The transplant in the system are to modify the three file system structure： OS_CPU_C。H OS_CPU。C, OS_CPU_A.ASM. Main transplantation procedure is as follows:A。 OS_CPU_C.HIt has defined the data types, the length and growth direction of stack in the processor。 Because different microprocessors have different word length，so the uC/OSII transplantation include a series of type definition to ensure its portability， and the revised code as follows：typedef unsigned char BOOLEAN;typedef unsigned char INT8U；typedef signed char INT8S;typedef unsigned short INT16U;typedef signed short INT16U;typedef unsigned int INT32U；typedef signed int INT32S；typedef float FP32；typedef double FP64；typedef unsigned int OS_STK；typedef unsigned int OS_CPU_SR；CortexM3 processor defines the OS_ENTER_CRITICAL (） and OS_EXIT_CRITICAL (） as opening and closing interrupt, and they must set to 32 bit of the stack OS_STK and CPU register length。 In addition, that has defined the stack pointer OS_STK_GROWTH stack growth direction from high address to lower address。B。 OS_CPU。CTo modify the function OSTaskStkInit（) according to the processor， the nine remaining user interface functions and hook functions can be null without special requirements, they will produce code for these functions only when the OS_CPU_HOOKS_EN is set to 1 in the file of OS_CFG.H。 The stack initialization function OSTaskStkInit (） return to the new top of the stack pointer.OS_CPU_A。ASMMost of the transplant work are completed in these documents， and modify the following functions。 OsStartHighRdy（） is used for running the most priority ready task， it will be responsible for stack pointer SP from the highest priority task of TCB control block, and restore the CPU， then the task process created by the user start to control the process。OSCtxSw （) is for task switching， When the current task ready queue have a higher priority task, the CPU will start OSCtxSw （) task switching to run the higher priority task and the current task stored in task stack。OSIntCtxSw （） has the similar function with OSIntSw (), in order to ensure real-time performance of the system， it will run the higher priority task directly when the interrupt come， and will not store the current task。OSTickISR (） is use to handle the clock interrupt， which needs interrupt to schedule its implementation when a higher priority task is waiting for the clock signal。OS_CPU_SR_Save () and OS_CPU_SR_Restore （) is completed to switch interrupt while entering and leaving the critical code both functions implement by the critical protection function OS_ENTER_CRITICAL （） and OS_EXIT_CRITICAL ().After the completion ofthe above work，uC/OSII can run on the processors。3.2. Software architectureFig.2 shows the system software architecture， so as to display the data visualized，uC/GUI3。90 and uC/OS-II is transplanted in the system, our system contains six tasks such data acquisition， data transmission， LCD display, touch screen driver, keypress management and uC/GUI interface。First of all, we should set the task priority and the task scheduling based on the priority。 It needs complete the required driver design before the data acquisition， such as A/D driver， touch panel driver and system initialization， while the initializations include: hardware platform initialization， system clock initialization, interrupt source configuration， GPIO port configuration， serial port initialization and parameter configuration， and LCD initialization。 The process is that the channel module sent sampling command to the AD channel， then to inform the receiver module it has been sent the sample start command， the receiver module is ready to receive and large data will store in the storage module, after the completion of the first sampling, channel module will send the complete command of sampling to the receiver module, the receiver sends an interrupt request to the storage module to stop the data storing, then the data will display on the LCD touch screen。 The data acquisition process shown in Fig。34.ExperimentsThe experiment of the embedded system has been done and data acquisition comes from the acceleration of MMA7455L， which is installed on the bench of rotating machine. The data acquisition have displayed as shown in Fig.4 and Fig。5， the system can select three channels to collect the vibration signal from the three directions of X, Y and Z-axis ， and in this paper the sampling frequency is 5KHZ and we have collect the vibration signal from normal state of unbalanced state at the same channel。 The result shows that our system can display real-time data acquisition and predict the preliminary diagnosis rapidly.5。ConclusionThis paper has designed an embedded signal acquisition system for real time according to the mechanical failure occurred with high frequency of in the rotating machines。 The system is based on a low cost microcontroller， Vibration signals is picked by the three axis acceleration sensor which has the performance of low cost and high sensitivity， and the acquisition data from axis x, y, and z. We have designed the system hardware structure， and analyses the working principle of data acquisition module. The proposed system of uC/OS-II realize the data task management and scheduling， and it is compacted with structure and low cost， whats more the system collects the vibration signal and analysis in realtime of the rotating machines， and then quickly gives diagnostic results。AcknowledgementsThis work was supported by The National Natural Science Foundation of China （51175169); China National Key Technology RD Program（2012BAF02B01); Planned Science and Technology Project of Hunan Province(2009FJ4055)；Scientific Research Fund of Hunan Provincial Education Department(10K023).REFERENCES1 Cheng, L。, Yu， H。, Research on intelligent maintenance unit of rotary machine， Computer Integrated Manufacturing Systems， vol。 10， Issue： 10， page 11961198， 2004。2 Yu, C。， Zhong， Ou。， Zhen, D。， Wei， F., 。Design and Implementation of Monitoring and Management Platform in Embedded Fault Diagnosis System, Computer Engineering， vol。 34 ， Issue: 8， page 264266， 2008.3Bi， D。， Gui， T., Jun, S。， Dynam 。 Behavior of a Highspeed Hybrid Gas Bearing-rotor System for a Rotating ramjet， Journal of Vibration and Shock， vol。 28, Issue： 9， page 79-80， 2009。4 Hai， L。, Jun, S.， Research of Driver Based on Fault Diagnosis System Data Acquisition Module， Machine Tool Hydraulics， vol. 38 ， Issue： 13, page 166168, 2011.5 Hao, W.， Qin， W., Xiao， S。, Optimized. Design of Embedded Parallel Data Acquisition System， Computer Engineering and Design， vol。 32, Issue： 5， page 16221625, 2011。6 Lei， S.， Ming， N., Design and Implementation of High Speed Data Acquisition System Based on FPGA, Computer Engineering， vol. 37， Issue: 19, page 221223, 2011。7 Chao， T., Ju