基于单片机的温湿度检测报警系统外文翻译.doc

译文：单片机温度控制系统中英文翻译资料at89s52是美国ATMEL公司生产的低电压，高性能CMOS8位单片机，片内含4Kbytes的快速可擦写的只读程序存储器（PEROM）和128 bytes的随机存取数据存储器（RAM），器件采用ATMEL公司的高密度、非易失性存储技术生产，兼容标准MCS-51产品指令系统，片内置通用8位中央处理器（CPU）和flish存储单元，功能强大at89s52单片机可为您提供许多高性价比的应用场合，可灵活应用于各种控制领域。主要性能参数：与MCS-51产品指令系统完全兼容4K字节可重复写flash闪速存储器1000次擦写周期全静态操作：0HZ24MHZ三级加密程序存储器128*8字节内部RAM32个可编程I/O口2个16位定时计数器6个中断源可编程串行UART通道低功耗空闲和掉电模式功能特性概述AT89S52提供以下标准功能：4K 字节flish闪速存储器，128字节内部RAM，32个I/O口线，两个16位定时计数器，一个5向量两级中断结构，一个全双工串行通信口，片内振荡器及时钟电路。同时，at89s52可降至0HZ的静态逻辑操作，并支持两种软件可选的节电工作模式。空闲方式停止CPU的工作，但允许RAM，定时计数器，串行通信口及中断系统继续工作。掉电方式保存RAM中的内容，但振荡器停止工作并禁止其它所有部件工作直到下一个硬件复位。方框图引脚功能说明Vcc：电源电压GND：地P0口：P0口是一组8位漏极开路型双向I/O口，也即地址/数据总线复位口。作为输出口用时，每位能吸收电流的方式驱动8个逻辑门电路，对端口写“1”可 作为高阻抗输入端用。 在访问外部数据存储器或程序存储器时，这组口线分时转换地址（低8位）和数据总线复用，在访问期间激活内部上拉电阻。P1口：P1是一个带内部上拉电阻的8位双向I/O口，P1的输出缓冲级可驱动（吸收或输出电流）4个TTL逻辑门电路。对端口写“1”，通过内部的上拉电阻把端口拉到高电平，此时可做熟出口。做输出口使用时，因为内部存在上拉电阻，某个引脚被外部信号拉低时会输出一个电流（Iil）.Flash编程和程序校验期间，P1接受低8位地址。P2口：P2是一个带有内部上拉电阻的8位双向I/O口，P2的输出缓冲级可驱动（吸收或输出电流）4个TTL逻辑门电路。对端口写“1”，通过内部地山拉电阻把端口拉到高电平，此时可作为输出口，作输出口使用时，因为内部存在上拉电阻，某个引脚被外部信号拉低时会输出一个电流（Iil）。在访问外部程序存储器获16位地址的外部数据存储器（例如执行 MOVX DPTR指令）时，P2口送出高8位地址数据。在访问8位地址的外部数据存储器（如执行 MOVX RI指令）时，P2口线上的内容（也即特殊功能寄存器（SFR）区中R2寄存器的内容），在整个访问期间不改变。Flash编程或校验时，P2亦接受高地址和其它控制信号。P3口：P3口是一组带有内部上拉电阻的8位双向I/O口。P3口输出缓冲级可驱动（吸收或输出电流）4个TTL逻辑门电路。对P3口写入“1”时，他们被内部上拉电阻拉高并可作为输出口。做输出端时，被外部拉低的P3口将用上拉电阻输出电流（Iil）。P3口除了作为一般的I/O口线外，更重要的用途是它的第二功能，如下表所示：端口引脚第二功能P3.0rxd (串行输入口)P3.1txd (串行输出口)P3.2int0 (外中断0)P3.3int1 (外中断1)P3.4t0 (定时/计数器0)P3.5t1 (定时/计数器1)P3.6 WR (外部数据存储器写选通)P3.7RD (外部数据存储器读选通)P3口还接收一些用于flash闪速存储器编程和程序校验的控制信号。RST：复位输入。当振荡器工作时，RST引脚出现两个机器周期以上高电平将使单片机复位。ALE/PROG：当访问外部程序存储器或数据存储器时，ALE（地址所存允许）输出脉冲用于所存地址的低8位字节。即使不访问外部存储器，ALE仍以时钟振荡频率的1/6输出固定的正脉冲信号，因此它可对外输出时钟或用于定时目的。要注意的是：每当访问外部数据存储器时将跳过一个ALE脉冲。对flash存储器编程期间，该引脚还用于输入编程脉冲（PROG）。如有不要，可通过对特殊功能寄存器（SFR）区中的8EH单元的D0位置位，可禁止ALE操作。该外置位后，只要一条MOVX和MOVC指令ALE才会被激活。此外，该引脚会被微弱拉高，单片机执行外部程序时，应设置ALE无效。PSEN：程序存储允许（PSEN）输出是外部程序存储器的读选通信号，当at89s52由外部程序存储器取指令（或数据）时，每个机器周期两个PSEN有效，即输出两个脉冲。在此期间，当访问外部数据存储器，这两次有效的PSEN信号不出现。EA/VPP:外部访问允许。欲使CPU仅访问外部程序存储器（地址为0000H-FFFFH），EA端必须保持低电平（接地）。需注意的是; 如果加密位LB1被编程，复位时内部会锁存EA端状态。如 EA端为高电平（接VCC端），CPU则执行内部程序存储器中的指令。Flash存储器编程时，该引脚加上+12V的编程允许电源VPP，当然这必须是该器件是使用12V编程电压VPP.XTAL1: 振荡器反相放大器的及内部时钟发生器的输出端。XTAL2: 振荡器反相放大器的输出端。时钟振荡器：at89s52中有一个用于构成内部振荡器的高增益反相放大器，引脚XTAL1和XTAL2分别是该放大器的输入端和输出端。这个放大器与作为反馈的片外石英晶体或陶瓷谐振器一起构成自激振荡器，振荡电路参见图5。外接石英晶体（或陶瓷谐振器）及电容C1、C2接在放大器的反馈回路中构成并联振荡电路。对外接电容C1、C2虽然没有十分严格的要求，但电容容量的大小会轻微影响振荡频率的高低、振荡器的稳定性、起振的难易程度及温度稳定性，如果使用石英晶体，我们推荐电容使用30PF+10PF，而如使用陶瓷谐振器建议选择40PF+10PF。用户也可以采用外部时钟。采用外部时钟的电路如图5右所示。这种情况下，外部时钟脉冲接到XTAL1端，即内部时钟发生器的输入端，XTAL2则悬空由于外部时钟信号是通过一个2分频触发器后作为内部时钟信号的，所以对外部时钟信号的占空比没有特殊要求，但最小高电平持续时间和最大的低电平持续时间应符合产品技术要求。空闲模式:在空闲工作模式状态，CPU保持睡眠状态而所有片内的外设仍保持激活状态，这种方式由软件产生。此时，片内RAM和所有特殊功能寄存器的内容保持不变。空闲模式可由任何允许的中断请求或硬件复位终止。终止空闲工作模式的方法有两种，其一是任何一条被允许中断的事件被激活，即可终止空闲工作模式。程序会首先响应中断，进入中断服务程序，执行完中断服务程序并仅随终端返回指令，下一条要执行的指令就是使单片机进入空闲模式那条指令后面的一条指令。其二是通过硬件复位也可将空闲工作模式终止，需要注意的是，当由硬件复位来终止空闲模式时，CPU通常是从激活空闲模式那条指令的下一条指令开始继续执行程序的，要完成内部复位操作，硬件复位脉冲要保持两个机器周期（24个时钟周期）有效，在这种情况下，内部禁止CPU访问片内RAM，而允许访问其它端口。为了避免可能对端口产生以外写入，激活空闲模式的那条指令后一条指令不应该是一条对端口或外部存储器的写入指令。空闲和掉电模式外部引脚状态模式程序存储器ALEPSENPORT0 PORT1PORT2PORT3空闲模式内部11数据数据数据数据空闲模式外部11浮空数据数据数据掉电模式内部00数据数据数据数据掉电模式外部00浮空数据数据数据掉电模式:在掉电模式下，震荡器停止工作，进入掉电模式的指令是最后一条被执行的指令，片内RAM和特殊功能寄存器的内容在终止掉电模式前被冻结。退出掉电模式的唯一方法是硬件复位，复位后将重新定义全部特殊功能寄存器但不改变RAM中的内容，在VCC恢复到正常工作电平前，复位应无效，且必须保持一定时间以使振荡器重启动并稳定工作。程序存储器的加密 ：AT89S52可使用对芯片上的3个加密位进行编程（P）或不编程（U）来得到如下表所示的功能：加密位保护功能表程序加密位保护类型LB1 LB2LB31UUU没有程序保护功能2PUU禁止从外部程序存储器中执行MOVC指令读取内部程序存储器的内容3PPU除上表功能外，还禁止程序校验4PPP除以上功能外，同时禁止外部执行当加密位LB1被编程时，在复位期间，EA端的逻辑电平被采样并锁存，如果单片机上电后一直没有复位，则锁存起的初始值是一个随机数，且这个随机数会一直保持到真正复位为止。为使单片机能正常工作，被锁存的EA电平值必须与该引脚当前的逻辑电平一致。此外，加密位只能通过整片擦除的方法清除。FLASH闪速存储器的编程：at89s52单片机内部有4K字节的FLASH PEROM,这个FLASH存储阵列出厂时已处于擦除状态（即所有存储单元的内容均为FFH），用户随时可对其进行编程。编程接口可接收高电平（+12V）或低电平（VCC）的允许编程信号，低电平编程模式适合于用户再线编程系统，而高电平编程模式可与通用EPROM编程器兼容。AT89S52单片机中，有些属于低电压编程方式，而有些则是高电平编程方式，用户可从芯片上的型号和读取芯片内的签名字节获得该信息，见下表。Vpp=12vVpp=5v芯片顶面标识at89s52xxxxyywwat89s52xxxx-5yyww签名字节(030H)=1EH(031H)=51H(032H)=FFH(030H)=1EH(031H)=51H(032H)=05HAT89S52的程序存储器阵列是采用字节写入方式编程的，每次写入一个字节，要对整个芯片内的PEROM程序存储器写入一个非空字节，必须使用片擦除的方式将整个存储器的内容清除。编程方法：编程前，需按表1、图3和图4所示设置好地址，数据及控制信号， at89s52编程方法如下：1.在地址线上加上要编程单元的地址信号。2.在数据线上加上要写入的数据字节。3.激活相应的控制信号。4.在高电压编程方式时，将EA/VPP端加上+12V编程电压。5.每对FLASH存储阵列写入一个字节或每写入一个程序加密位，加上一个ALE/PROG编程脉冲，改变编程单元的地址和写入的数据，重复15步骤，直到全部文件编程结束。每个字节写入周期是自身定时地，通常约为1.5ms。数据查询：at89s52单片机用数据查询方式来检测一个写周期是否结束，在一个写周期中，如需要读取最后写入的那个字节，则读出的数据的最高位（P0.7）是原来写入字节最高位的反码。写周期完成后，有效的数据就会出现在所有输出端上，此时，可进入下一个字节的写周期，写周期开始后，可在任意时刻进行数据查询。READY/BUSY：字节编程的进度可通过“RDY/BSY”输出信号监测，编程期间，ALE变为高电平“H”后P3.4(RDY/BSY)端电平被拉低，表示正在编程状态（忙状态）。编程完成后，P3.4变为高电平表示准备就绪状态。程序校验：如果加密位LB1、LB2没有进行编程，则代码数据可通过地址和数据线读回原编写的数据。加密位不可能直接变化。证实加密位的完成通过观察它们的特点和能力。芯片擦除：利用控制信号的正确组合（表1）并保持ALE/PROG引脚10ms的低电平脉冲宽度即可将PEROM阵列（4k字节）整片擦除，代码阵列在擦除操作中将任何非空单元写入“1”，这步骤需要再编程之前进行。读片内签名字节：at89s52单片机内有3个签名字节，地址为030H、031H和032H。用于声明该器件的厂商、型号和编程电压。读签名字节的过程和单元030H、031H和032H的正常校验相仿，只需将P3.6和P3.7保持低电平，返回值意义如下：（030H）=1EH声明产品由ATMEL公司制造。（031H）=51H声明为at89s52单片机。（032H）=FFH声明为12V编程电压。（032H）=05H声明为5V编程电压。编程接口：采用控制信号的正确组合可对FLASH闪速存储阵列中的每一代码字节进行写入和存储器的整片擦除，写操作周期是自身定时的，初始化后它将自动定时到操作完成。AT89S52 single chip microcomputerThe at89s52 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash Programmable and Erasable Read Only Memory (PEROM) and 128 bytes RAM. The device is manufactured using Atmels high density nonvolatile memory technology and is compatible with the industry standard MCS-51 instruction set and pinout. The chip combines a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel at89s52 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications.Features: Compatible with MCS-51 Products 4K Bytes of In-System Reprogrammable Flash Memory Endurance: 1,000 Write/Erase Cycles Fully Static Operation: 0 Hz to 24 MHz Three-Level Program Memory Lock 128 x 8-Bit Internal RAM 32 Programmable I/O Lines Two 16-Bit Timer/Counters Six Interrupt Sources Programmable Serial Channel Low Power Idle and Power Down ModesThe at89s52 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator and clock circuitry. In addition, the at89s52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power Down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.Pin Description:VCC Supply voltage.GND Ground.Port 0Port 0 is an 8-bit open drain bidirectional I/O port. As an output port each pin can sink eight TTL inputs. When is are written to port 0 pins, the pins can be used as high impedance inputs. Port 0 may also be configured to be the multiplexed loworder address/data bus during accesses to external program and data memory. In this mode P0 has internal pullups. Port 0 also receives the code bytes during Flash programming, and outputs the code bytes during program verification. External pullups are required during program verification.Port 1Port 1 is an 8-bit bidirectional I/O port with internal pullups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 1 also receives the low-order address bytes during Flash programming and verification.Port 2Port 2 is an 8-bit bidirectional I/O port with internal pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX DPTR). In this application it uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification.Port 3Port 3 is an 8-bit bidirectional I/O port with internal pullups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups. Port 3 also serves the functions of various special features of the at89s52 as listed below:Port pinalternate functionsP3.0rxd (serial input port)P3.1txd (serial output port)P3.2int0 (external interrupt0)P3.3int1 (external interrupt1)P3.4t0 (timer0 external input)P3.5t1 (timer1 external input)P3.6 WR (external data memory write strobe)P3.7rd (external data memory read strobe)Port 3 also receives some control signals for Flash programming and verification.RSTReset input. A high on this pin for two machine cycles while the oscillator is running resets the device.ALE/PROGAddress Latch Enable output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during Flash programming.In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency, and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external Data Memory. If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode.PSENProgram Store Enable is the read strobe to external program memory. When the at89s52 is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory.EA/VPPExternal Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt programming enable voltage(VPP) during Flash programming, for parts that require 12-volt VPP.XTAL1Input to the inverting oscillator amplifier and input to the internal clock operating circuit.XTAL2Output from the inverting oscillator amplifier.Oscillator CharacteristicsXTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 1. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 2. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed.Idle ModeIn idle mode, the CPU puts itself to sleep while all the onchip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special functions registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset.It should be noted that when idle is terminated by a hard ware reset, the device normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory. Status of External Pins During Idle and Power Down ModesmodeProgram memoryALEpsenPort0 Port1Port2Port3idleinternal11datadatadataDataIdleExternal11floatDatadataDataPower downInternal00DataDataDataDataPower downExternal 00floatdataDatadataPower Down ModeIn the power down mode the oscillator is stopped, and the instruction that invokes power down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the power down mode is terminated. The only exit from power down is a hardware reset. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize.Program Memory Lock BitsOn the chip are three lock bits which can be left unprogrammed (U) or can be programmed (P) to obtain the additional features listed in the table below: Lock Bit Protection ModesWhen lock bit 1 is programmed, the logic level at the EA pin is sampled and latched during reset. If the device is powered up without a reset, the latch initializes to a random value, and holds that value until reset is activated. It is necessary that the latched value of EA be in agreement with the current logic level at that pin in order for the device to function properly.Programming the Flash：The at89s52 is normally shipped with the on-chip Flash memory array in the erased state (that is, contents = FFH) and ready to be programmed. The programming interface accepts either a high-voltage (12-volt) or a low-voltage (VCC) program enable signal. The low voltage programming mode provides a convenient way to program the at89s52 inside the users system, while the high-voltage programming mode is compatible with conventional third party Flash or EPROM pro