建筑工程土木毕业设计方案中英文翻译.doc

英文原文 Components of A Building and Tall BuildingsAndre1. AbstractMaterials and structural forms are combined to make up the various parts of a building，including the load-carrying frame，skin，floors，and partitions. The building also has mechanical and electrical systems，such as elevators，heating and cooling systems，and lighting systems. The superstructure is that part of a building above ground，and the substructure and foundation is that part of a building below ground.The skyscraper owes its existence to two developments of the 19th century：steel skeleton construction and the passenger elevator. Steel as a construction material dates from the introduction of the Bessemer converter in 1885.Gustave Eiffel (1832-1932) introduced steel construction in France. His designs for the Galerie des Machines and the Tower for the Paris Exposition of 1889 expressed the lightness of the steel framework. The Eiffel Tower，984 feet (300 meters) high，was the tallest structure built by man and was not surpassed until 40 years later by a series of American skyscrapers.Elisha Otis installed the first elevator in a department store in New York in 1857.In 1889，Eiffel installed the first elevators on a grand scale in the Eiffel Tower，whose hydraulic elevators could transport 2,350 passengers to the summit every hour.2. Load-Carrying FrameUntil the late 19th century，the exterior walls of a building were used as bearing walls to support the floors. This construction is essentially a post and lintel type，and it is still used in frame construction for houses. Bearing-wall construction limited the height of building because of the enormous wall thickness required；for instance，the 16-story Monadnock Building built in the 1880s in Chicago had walls 5 feet (1.5 meters) thick at the lower floors. In 1883，William Le Baron Jenney (1832-1907) supported floors on cast-iron columns to form a cage-like construction. Skeleton construction，consisting of steel beams and columns，was first used in 1889. As a consequence of skeleton construction，the enclosing walls become a “curtain wall” rather than serving a supporting function. Masonry was the curtain wall material until the 1930s，when light metal and glass curtain walls were used. After the introduction of buildings continued to increase rapidly. All tall buildings were built with a skeleton of steel until World War . After the war，the shortage of steel and the improved quality of concrete led to tall building being built of reinforced concrete. Marina Tower (1962) in Chicago is the tallest concrete building in the United States； its height588 feet (179 meters)is exceeded by the 650-foot (198-meter) Post Office Tower in London and by other towers.A change in attitude about skyscraper construction has brought a return to the use of the bearing wall. In New York City，the Columbia Broadcasting System Building，designed by Eero Saarinen in 1962,has a perimeter wall consisting of 5-foot (1.5meter) wide concrete columns spaced 10 feet (3 meters) from column center to center. This perimeter wall，in effect，constitutes a bearing wall. One reason for this trend is that stiffness against the action of wind can be economically obtained by using the walls of the building as a tube； the World Trade Center building is another example of this tube approach. In contrast，rigid frames or vertical trusses are usually provided to give lateral stability.3. SkinThe skin of a building consists of both transparent elements (windows) and opaque elements (walls). Windows are traditionally glass，although plastics are being used，especially in schools where breakage creates a maintenance problem. The wall elements，which are used to cover the structure and are supported by it，are built of a variety of materials：brick，precast concrete，stone，opaque glass，plastics，steel，and aluminum. Wood is used mainly in house construction； it is not generally used for commercial，industrial，or public building because of the fire hazard.4. FloorsThe construction of the floors in a building depends on the basic structural frame that is used. In steel skeleton construction，floors are either slabs of concrete resting on steel beams or a deck consisting of corrugated steel with a concrete topping. In concrete construction，the floors are either slabs of concrete on concrete beams or a series of closely spaced concrete beams (ribs) in two directions topped with a thin concrete slab，giving the appearance of a waffle on its underside. The kind of floor that is used depends on the span between supporting columns or walls and the function of the space. In an apartment building，for instance，where walls and columns are spaced at 12 to 18 feet (3.7 to 5.5 meters)，the most popular construction is a solid concrete slab with no beams. The underside of the slab serves as the ceiling for the space below it. Corrugated steel decks are often used in office buildings because the corrugations，when enclosed by another sheet of metal，form ducts for telephone and electrical lines.5. Mechanical and Electrical SystemsA modern building not only contains the space for which it is intended (office，classroom，apartment) but also contains ancillary space for mechanical and electrical systems that help to provide a comfortable environment. These ancillary spaces in a skyscraper office building may constitute 25% of the total building area. The importance of heating，ventilating，electrical，and plumbing systems in an office building is shown by the fact that 40% of the construction budget is allocated to them. Because of the increased use of sealed building with windows that cannot be opened，elaborate mechanical systems are provided for ventilation and air conditioning. Ducts and pipes carry fresh air from central fan rooms and air conditioning machinery. The ceiling，which is suspended below the upper floor construction，conceals the ductwork and contains the lighting units. Electrical wiring for power and for telephone communication may also be located in this ceiling space or may be buried in the floor construction in pipes or conduits.There have been attempts to incorporate the mechanical and electrical systems into the architecture of building by frankly expressing them； for example，the American Republic Insurance Company Building(1965) in Des Moines，Iowa，exposes both the ducts and the floor structure in an organized and elegant pattern and dispenses with the suspended ceiling. This type of approach makes it possible to reduce the cost of the building and permits innovations，such as in the span of the structure.6. Soils and FoundationsAll building are supported on the ground，and therefore the nature of the soil becomes an extremely important consideration in the design of any building. The design of a foundation dependson many soil factors，such as type of soil，soil stratification，thickness of soil lavers and their compaction，and groundwater conditions. Soils rarely have a single composition； they generally are mixtures in layers of varying thickness. For evaluation，soils are graded according to particle size，which increases from silt to clay to sand to gravel to rock. In general，the larger particle soils will support heavier loads than the smaller ones. The hardest rock can support loads up to 100 tons per square foot(976.5 metric tons/sq meter)，but the softest silt can support a load of only 0.25 ton per square foot(2.44 metric tons/sq meter). All soils beneath the surface are in a state of compaction； that is，they are under a pressure that is equal to the weight of the soil column above it. Many soils (except for most sands and gavels) exhibit elastic propertiesthey deform when compressed under load and rebound when the load is removed. The elasticity of soils is often time-dependent，that is，deformations of the soil occur over a length of time which may vary from minutes to years after a load is imposed. Over a period of time，a building may settle if it imposes a load on the soil greater than the natural compaction weight of the soil. Conversely，a building may heave if it imposes loads on the soil smaller than the natural compaction weight. The soil may also flow under the weight of a building； that is，it tends to be squeezed out.Due to both the compaction and flow effects，buildings tend settle. Uneven settlements，exemplified by the leaning towers in Pisa and Bologna，can have damaging effectsthe building may lean，walls and partitions may crack，windows and doors may become inoperative，and，in the extreme，a building may collapse. Uniform settlements are not so serious，although extreme conditions，such as those in Mexico City，can have serious consequences. Over the past 100 years，a change in the groundwater level there has caused some buildings to settle more than 10 feet (3 meters). Because such movements can occur during and after construction，careful analysis of the behavior of soils under a building is vital.The great variability of soils has led to a variety of solutions to the foundation problem. Wherefirm soil exists close to the surface，the simplest solution is to rest columns on a small slab of concrete(spread footing). Where the soil is softer，it is necessary to spread the column load over a greater area；in this case，a continuous slab of concrete(raft or mat) under the whole building is used. In cases where the soil near the surface is unable to support the weight of the building，piles of wood，steel，or concrete are driven down to firm soil.The construction of a building proceeds naturally from the foundation up to the superstructure. The design process，however，proceeds from the roof down to the foundation (in the direction of gravity). In the past，the foundation was not subject to systematic investigation. A scientific approach to the design of foundations has been developed in the 20th century. Karl Terzaghi of the United States pioneered studies that made it possible to make accurate predictions of the behavior of foundations，using the science of soil mechanics coupled with exploration and testing procedures. Foundation failures of the past，such as the classical example of the leaning tower in Pisa，have become almost nonexistent. Foundations still are a hidden but costly part of many buildings. The early development of high-rise buildings began with structural steel framing. Reinforced concrete and stressed-skin tube systems have since been economically and competitively used in a number of structures for both residential and commercial purposes. The high-rise buildings ranging from 50 to 110 stories that are being built all over the United States are the result of innovations and development of new structural systems.Greater height entails increased column and beam sizes to make buildings more rigid so that under wind load they will not sway beyond an acceptable limit. Excessive lateral sway may causeserious recurring damage to partitions，ceilings，and other architectural details. In addition，excessive sway may cause discomfort to the occupants of the building because of their perception of such motion. Structural systems of reinforced concrete，as well as steel，take full advantage of the inherent potential stiffness of the total building and therefore do not require additional stiffening to limit the sway.中文译文建筑及高层建筑构成安得烈1 摘要材料和构造类型是构成建筑物各方面构成某些，这些某些涉及承重构造、围护构造、楼地面和隔墙。建筑物内部尚有机械和电气系统，例如电梯、供暖和制冷系统、照明系统等。建筑中高于地面某些称为上部构造，而地面如下某些称为地下构造和基本。摩天大楼浮现应归功于19世纪两个新创造：钢构造建筑和载人电梯。钢材作为构造材料应用来源于1855年贝色麦炼钢法。古斯塔艾菲尔（18321923）在初次简介钢构造建筑是在法国。她在1889年巴黎国际博览会所设计艾菲尔铁塔，完美呈现了钢构造轻巧。艾菲尔铁塔高300米，是当时人类建造最高建筑物，并且直到40年后才被美国摩天大楼超越。第一部电梯是1857年Elisha Otis给纽约一家百货公司所安装。1889年，艾菲尔在艾菲尔铁塔上安装了第一部大型液压电梯，它每小时可以运送2350位乘客到达塔顶。2 承重框架直到19世纪后期，建筑物外墙还仍被用做承重墙来支撑楼层，这种构造是基本一种过梁类型，并且它也被用在框架构造房屋中。由于所需墙体厚度很大，承重墙构造限制了建筑物高度；例如，1880年建于芝加哥16层高Monadnock Building，在较低楼层墙体厚度已达到1.5米。1883年，Willian Le Baron Jenney（18321907）用类似鸟笼形状铁柱来支撑楼层。1889年，框架构造初次由钢梁和钢柱构成。外墙成为了而不只是被用做支撑构造是框架构造一种成果。自从钢骨架初次推出，建筑物高度也始终在迅速增长。第二次世界大战前，所有高层建筑都是由钢骨架建造。战争结束后，钢材缺少和混凝土质量改进，增进了钢筋混凝土高层建筑发展。芝加哥Marina Towers（1962）是当时美国最高混凝土建筑；它高度是588英尺即179米，但是不久它就被高650英尺即195米伦敦邮政塔和其他某些塔所超过。人们关于摩天大楼态度转变使承重墙重新得到了应用。在纽约，由Eero Saarinen于1962年设计哥伦比亚广播公司大楼，四周墙由1.5米宽混凝土柱构成，柱与柱中心间距为3米。这种围护墙有效地构成了建筑物承重墙。这种趋势发展因素之一是建筑物墙像一种管道同样可以有利地抵抗风强烈作用；世贸大楼就是另一种应用管道法例子。相比之下，结实框架或垂直支撑则普通会使建筑横向更稳定。3 围护构造一种建筑围护构造由透明窗户和不透明墙构成。窗户普通采用老式上玻璃作为材料，然而塑料也被使用，特别在破损严重和难以保持学校里。墙被用来覆盖构造和起支撑作用，它是由多样化建筑材料构成：砖、现浇混凝土、石头、不透明玻璃、塑料、钢材和铝材。木头是过去建造房屋重要材料；但由于易燃，普通不惯用于用于商业、工业和公共建筑。4 楼地面一幢建筑楼地面构造取决于它所使用基本构造框架。在钢框架建筑中，楼地面或者是钢梁上混凝土楼板，或者是由波纹钢配有混凝土骨料构成地板。在混凝土构造中，楼地面或者是混凝土梁上混凝土楼板或者是一系列紧密分布于混凝土梁在方向上端薄混凝土楼板，在它下面抹一层抹面。这种楼地面应用取决于支撑柱之间距离或者墙和空间功能性。在一栋公寓大楼中，例如，当墙和柱隔开3.7米到5.5米时，最常用构造是无梁实心混凝土楼盖。楼盖下表面是楼盖如下空间最高限度。而波纹钢地板则惯用于办公大楼中，这是由于当波纹钢地板波纹被另一块金属板盖上时，可以形成电话线和电线管道。5 机械与电力系统一种当代建筑不但要有必要使用空间并且也要涉及机械、电力系统等辅助空间，以便提供一种舒服生活环境。这些辅助空间也许占摩天大楼总建筑面积25%。在一种办公大楼中，供暖、通风、电力和卫生设备系统预算额占实际建筑总预算额40%，这足以显示它们在建筑中重要性。由于当前许多建筑被建导致密封，窗户不能被打开，因而便要由机械系统提供通风设备和空气调节设备。管道将新鲜空气从通过中央换气室和空气调节器源源不断输入建筑物内。悬挂在上面楼层构造下面天花板可以把通风管和控制器设备遮挡住以保持美观。提供动力电力线路和电话通讯线路也也许被安顿在天花板或者楼地面构造层中管道或导线管里。咱们曾试着把机械建造、电力系统加入建筑物建筑风格中去，让她们裸露在构造外部；例如建造与1956年位于Des Morines美国保险公司大楼，管道和楼地面构造就被有序、优美悬挂在天花板上。这种建造办法极大减少了建导致本，同步带来了新构造形式。例如在构造间距方面革新。6 土和地基所有建筑物都是靠土层支撑在地面上，因而土特性成为建筑设计时极其重要考虑因素。基本设计很大限度上仍要考虑土许多因素，例如土类型，土分层状况，土层厚度和它密实度，以及地下水状况等。土层很少只具有单一物质；她们普通是厚度不同混合状态土层。据评估，土层级别是依照土分子大小来划分，从小到大依次是淤泥、粘土、沙、石子、岩石。普通，较大分子土支撑荷载要不不大于那些小分子荷载力。最坚硬岩石可以支撑荷载大概是每平方米100吨，而最软淤泥仅可以支撑荷载大概是每平方米0.25吨。所有地表如下土都处在受压状态，说得更精准些，这些土承受与作用在其上土柱重量相等压力。许多土显示出弹性性质她们或被重载压坏或卸载后又恢复。土弹性常随时间而变化，也就是说，土层变形在恒载作用下随着时间增长而不断地变化。过一段时间后，如果加于土层上荷载不不大于土自然压紧状态下重量，则建筑物不会产生沉降，反之则会沉降。建筑物重量也许会使土产生流动；也就是说，经常会发生土被挤浮现象。土受压和流动双重影响，使建筑物发生沉降。不均匀沉降例如比萨斜塔，损坏成果是建筑物发生倾斜，墙和隔墙也许浮现裂缝，窗户和门也许产生变形，或者甚至建筑也许崩塌。均匀沉降不会如此严重，尽管也许浮现危险状况，例如墨西哥城某些建筑，浮现各种各样后果，在过去一百年里，由于地下水位发生了变化，导致某些建筑下沉了3米多。由于类似状况也许发生在建造时也也许是建造后，因而小心解决建筑物下土层是极其重要。土层巨大变化使得解决地基问题办法也变得多样化。如果表面土层下土为坚硬土层，最简朴办法是采用混凝土基本。若是软弱土层，则加大柱面积；这种状况下，整个建筑就可采用筏板基本。假设表面土层不可以支撑建筑物重量，木构造建筑、钢构造建筑、或者混凝土建筑应建造在坚硬土层上。建造一幢建筑物普通是从基本开始到上部构造。然而设计过程是从屋顶开始到基本。在过去，地基解决不是一种系统研究项目。在20世纪，一种科学地基设计办法已经发展起来了。美国Karl Teraghi不断创造研究，使土力学和土地勘测联合起来，让它尽量精确地预测地基活动状态。过去典型地基破坏例子比萨斜塔当前变得几乎不存在了。而地基依然是建筑物中不可见某些费用最大一某些。初期高层建筑发展是以型钢构造开始。钢筋混凝土和薄壳筒体体系已经以节俭和竟争为目被应用于住宅和商业建筑中。作为新构造体系创新和发展成果，美国处处都是50到110层高层建筑。巨大高度需要增长柱和梁尺寸来使建筑物更加结实，为是在风荷载作用下不致于使其倾斜度超过限值。重复地侧向摆动也许引起隔墙天花板和其他建筑部件损坏。此外，过度摆动也许会给建筑物中居住者带来不安和恐惊，由于会使她们有移动感觉。钢筋混凝土构造体系和钢构造同样，内在潜力使得建筑物非常坚硬因而不需要附加强化来限制摆动。