资源描述
单击此处编辑母版标题样式,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,*,单击此处编辑母版标题样式,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,*,单击此处编辑母版标题样式,单击此处编辑母版文本样式,第二级,第三级,第四级,第五级,*,WAT电性参数介绍,WAT电性参数介绍WAT电性参数介绍FlowWhy WAT?,WAT Parameter Review.,Process test Methodology.,Device test Methodology.,Process Factor Influence on WAT Para.,WAT Application,General Guide-line when WAT fail,Example introduce,2,Flow,Why WAT?,WAT Parameter Review.,Process test Methodology.,Device test Methodology.,Process Factor Influence on WAT Para.,WAT Application,General Guide-line when WAT fail,Example introduce,2,Why WAT?,Debug the Process Error.,Monitor Process Window.,Check Design Rule.,Control the Process Parameters(SPC).,Reliability Characterization.,Device Modeling for Circuit Design.,Develop next Generation.,3,(,in=13206.24614.8),TST2,TST1,TST7,TST3,TST4,TST8,TST9,TST5,TST6,(,out=13326.24734.8),(0.0),frame=120 x120,Test site and Test line location,4,Device Categorization,Active Device,MOSFET(N/P),Field,Transistor,BJT,Diode,Passive,Device,Resistor,Capacitors,Design,rules,Isolation,lines(Spacing,Continuity),contact,extension,Resistor,Diffusion regions,N+,N-,P+,N-Well,P-Well,Deep-NW,Thin films,P1,P2,M1,M2,M3,Contact:,C3 to N+/P+,Via,C3 to P1,P2,5,WAT Parameter Review,Process Part:,Spacing(Bridge,short),Continuity(Open),Isolation,Sheet,Rs,Contact,Rc,Kelvin Structure for Resistance,Integrity(Inter layer dielectric),Extension rule check,CD measurement,Junction leakage,Device Part:,Gm(,Vth,Current Gain),Idsat,(,Asym,),Ioff,Swing,Gamma factor,BKV,Isub,Leff,Rext,Weff,Field Device test,Capacitance,6,Process Part:,(1)Spacing(Bridge,short),Define:,验证在Process中,同层/同层之间的隔绝能力!,Measurement method:,Force 1uA电流到导线上,假若线路中有short,则测量出的电压值就偏低(50,的结构中,Force I=0.01uA and Voltage lim=10V!(Req=L/W),Pad1,Pad2,Pad3,Pad4,1um,15um,70um,2um(W),70um,1000,L,12,Process Part:,(7)Integrity(Gate-Oxide-Integrity),Define:,验证,Gate oxide,的,Quality,好坏之一项参数当,Gate oxide uniformity,不均,或,Interface,间有,defects,时,会形成一漏电流路径失去,Oxide Isolation,的能力!,Measurement method:,一般测量法不外乎,Force V/I and measure I/V,1.Force V and measure I:,Sweep Volt on Poly gate,and Vb=ground,then measure Ig(aboutpA),If Ig increase,to 1uA,this Sweep Volt is BKV(normal large 7 V),2.Force I and measure V:,Force 1uA on Poly gate then measure Voltage,PS:,测量方式取决于Pattern design(common pad issue),WELL,Poly Gate,13,Process Part:,(8)Extension rule check,Define:,以,sense,漏电流的方式,测量,Contact overlay,的,Design rule check!,PS,:(1),一般来说,,layout,的结构会采用十字架的形式,最大的好处是在把,shot issues,的问题抓出!,(2)miss-align,与,contact number,无关!,M2,Via,M1,M1 ext to via,用Poly4垫,14,Process Part:,(9)CD measurement,Define:,籍由测量两条同长度,不同宽度的电阻,换算出其宽度,CD,大小!,PS:,当,W=W1,时 可测量得电阻R1,W=W2,时 可测量得电阻R2,R1=Rs*L/(W1-,W)R2=Rs*L/(W2-,W),R1/R2=(W2-,W)/(W1-,W),则,W(CD loss),Rs,皆可求得!,(P1 CD,大小影响到,Channel length,的长短,需特别注意,),15,Process Part:,(10)Junction leakage,Define:,一般来说,leakage,指的是反向偏压时的漏电流测量,通常有以下三种分类:,1.Contact leak 2.Dielectric leak(usually for DRAM)3.Junction leak(bulk or peri),PS:I-bulk(meas)=A-bulk*J-area(current/um2)+L-peri*J-peri(current/um),I-finger(meas)=A-fing*J-area(current/um2)+L-peri(current/um)(J-area,J-peri 可求),PW拉出,NAA有打Blanket N+imp,N-imp,C3,M1,16,Device Part:,Gm(,Vth,Current Gain),Define:Gm=(,Id/Vg),Linear:,Id=1/2(,CoxW,/L)(2(,Vgs,-,Vt,),Vds,-Vds,2,),Gm=,CoxW,/L,Saturation:,Id=1/2(,CoxW,/L)(,Vgs,-,Vt,),2,Gm=,CoxW,/L(,Vgs,-,Vt,),Pinch-Off:,Vds,=,Vgs,-,Vt,Gm=Cox(W/L),Vds,=Cox(W/L),PS:,If value abnormal,It may have,Gox,Leff,or implant issues.,Vth,Measure method:,Step1:,Vds,=0.1 Vs=,Vb,=0 and swoop Vg,Step2:Plot Ids,Vgs,and Gm,Vgs,curves,Step3:find Gm(max),plot slop of this point on Ids,Vgs,From Linear function set Id=0then,Vth,=,Vgs,-V,0,3,V,g,I,d,17,Device Part:,Idsat,(,Asym,),Define:,Idsat,=Ids at,Vgs,=,Vds,=,Vcc,Ids Measure method:,Step1:Vs=,Vb,=0,Vd,=,Vcc,and Sweep Vg,Step2:Plot Ids,Vgs,Step3:Find Ids at Vg=,Vd,=,Vcc,Ids Asymmetry check:,Step1:Following the Ids measurement.,Step2:Change Drain and Source Pin-assign,then measure Ids.,Step3:,Asym,=ABS(Ids-Ids)/Ids,PS:,If Ids Asymmetry,Avnormal,It may,have the,Isub,(or Poly gate non-overlap,issues)or LDD N-,Rs,or Contact,Rc,some things trouble!,A,SMU2,Vg,G,D,S,Sub,Vsub,SMU3,Id,Vd,SMU1,18,Device Part:,Ioff,Define:Ids=,Ioff,at,Vgs,=Vs=,Vb,=0,Vds,=,Vcc,Ioff,Measure method(Direct meas.):,Step1:Vs=,Vb,=0,Vd,=,Vcc,and Sweep Vg,Step2:Plot Ids,Vgs,Stop3:Find Ids at Vg=0,Ps:,测量机台的灵敏度,须注意与曲线的相,关联性!,Ioff,Measure method(,外插法,):,Step1:Follow the,Ioff,Direct meas.method,Step2:Plot Max slop of this curve on log(Ids),Vgs,Step3:Find the Ids at Vg=0 intercept.,logId,Vg,Vd=Vcc,logId,Vg,Vd=Vcc,19,Device Part:,Swing(,Subthreshold,Slop,St),Define:Swing=(,log(Ids)/,Vgs,),-1,=2(,kt,/q)(1+,Cd,/Cox),*,当,Vg,逐渐增加,channel accumulation,deplation,weak,inversionstrong inversion,Swing,既是测量,weak inversion,时,Id,与,Vg,的变化程度,!(,exponential),DIBl,effect measurement:,Step1:Vs=,Vb,=,Vd,=and Sweep Vg,Step2:Plot log(Ids),Vgs,Step3:Plot Max slop of this curve on log(Ids),Vgs,Step4:Repeat(a)but,Vd,=,Vcc,Step5:Repeat(b),PS:,如果发生,punch-through(Subsurface-DIBL),High drain St,will larger than Low drain.(Swing,越大,Leakage,越大,),0,1,V,DS,=5V,V,DS,=0.1V,V,G,I,D,20,Device Part:,Gamma factor,Define:,=(2qNa,1/2,/Cox=,Vt,/(2,f,+Vbs1),1/2,-(2,f,+Vbs2),1/2,),Vt,=,Vf,+2,f,+(2,qNb,(2,f,+,Vsb,),1/2,/Cox,*Gamma factor,是在,计算,Substrate,与,Source,间非等电位时,对,Vt,变化的影响,.(,Vt,值需,依,Vbs,的大小改变来计算,),Measurement method:,Step1:Fixed,Vd,=V,Step2:Measure,Vt,under various,Substate,bias.,Step3:Plot,Vt,versus(,2,f,+,Vbs,),1/2,curve,Step4:slope of the curve is taken to be,Gammar,factor.,PS:,Vt adjusment,Deep implant,well implant,well implant,都会影响此一参数,通常,Vt,浓,度越高,,值越大,!,同理,不同的,device,在相,同的,Back-bias,测量下,,Vt,差,值,亦代表着,值的影响,V,D,V,G,N,2,N,1,21,Device Part:,BKV,Define:Drain voltage which produces 1uA,Drain Current,.,Breakdown Voltage,是用来,test MOS,的耐压程度。,(1),在,Long channel,的,Device,,,看的是,S/D to well,间,junction,的崩溃电压,(2),在,Short channel,的,status,,,看到的,BKV,,,有可,能是来自,drain to source,因,punch-through,造成,的低电压现象,!,PS:,可籍由,Id,流到,Is or,Ib,来判断,BKV,由何种造成!,Measurement method:,Step1:Vs=Vg=,Vb,=V,Step2:set up Drain current limited at 1uA.,Step3:Plot Ids,Vds,Step4:Sweep,Vd,and find the Voltage at Id=1uA,N+,N+,V,S,V,G,V,D,V,B,22,Device Part:,Isub,Define:,Isub,(Measure MOS hot carrier,effect.),Isub,=f(,Vds,Vgs,),(1),Vds,对,Isub,impact:,Pinch off point,VDsat,=,Vgs,Vt,If,Vds,VD-,Vdsat,then,Emax,Isub,(2),Vgs,对,Isub,impact:,一开始,Vgs,Id,then,Isub,但当过,pinch,off point,时,Vgs,VD-,Vdsat,then,Emax,Isub,Measurement method:,Step1:Vs=,Vb,=0V,and,Vd,=,Vcc,Step2:Sweep Vg(,Vgmin,1/2Vd),Step3:Plot,Isub,Vgs,Step4:,Isub,=,Isubmax,PS:,If,Isub,abnormal,it may cause from hot,carrier,Poly gate non-overlap,Contact over,etchingand so on.,A,Vg,G,D,S,Sub,Isub,SMU3,Id,Vd,SMU2,SMU1,A,Vsub,Measurement Circuit,0,Method,Characteristics,Isub,Vg,Peak Point,Vg limit=Vd,23,Device Part:,Leff,Weff,and,Rext,Define:,Leff,=,Lmask,-2,L,Rext,=,Rm,-,Rchannel,Weff,=,Wmask,-2 W,公式推导:,I,DS,=(,Weff,/,Leff,)*Cox*,n,*(,Vgs,-,Vt,-0.5V,DS,)V,DS,Rch,=V,DS,/I,DS,=,Leff,/(,Weff,*Cox*,n,*(,Vgs,-,Vt,-,0.5V,DS,),Rm,=,Vf,/,Im,=,Rext,+,Rch,=,Rext,+A(,Lmask,-2L),A=1/(,Weff,*Cox*,n,*(,Vgs,-,Vt,-0.5V,DS,),Measurement method:,Step1:Fixed VDS=0.1V,Vb,=Vs=0V,Step2:,变化,Vgs,-,Vt,=2,3V,Step3:Plot,Rm Lmask,Step4:,选,相同的,Channel Width,不同的,length,的,device,测量不同的,Vgs,-,Vt,Bias,下的,I,DS,计算,Rm,=V,DS,/I,DS,Step5:,计算两直线交点,X,轴截距,=2,L,(2,W,算法同),Y,轴截距,=,Rext,0,1,4,3,2,5,6,7,Rext=16,50,100,150,200,V,DS,=0.1V,V,gS,=0,V,GS,=6V,V,GS,=8V,V,GS,=10V,V,GS,=12V,V,GS,=14V,24,Device Part:,Field Device test,Define:,测量,Active region,与,field oxide,所,形成的寄生元件之,Isolation,能力测,试!,考虑不同的,layout,结构,有以下两种测量法:,Measurement method:,Field Oxide,上有导电材料覆盖:,此结构如同一,AMOS,元件,,MOS,Vt,的大,小,即反映出,Field Isolation,能力的好坏!,PS:,测量方法同,Vth,测量法!,(2),Field oxide,上无导电材料覆盖:,此结构考虑,Acitve,range,间,implant,浓度的,Isolation,能力,一般是测量,Constant,current(1uA),下的耐压度,Poly,AA,FOX,25,Device Part:,Capacitance(thickness,meas,),Define:,电容的结构常见的有一般介质电,容与,MOS,电容两大类,差别在参,考极板的组成成分!,Measurement method,:,(HP4284),(1)For,一般介质电容:,Force Voltage,的极性与电容大小无关!,(2),for MOS,电容:,Gox,电容的测量方面,要避免空乏层,电容的形成,才能算出,Thickness,Poly on PW:,加负压于,Poly gate,上,PW,接地!,Poly on NW:,加正压于,Poly gate,上,NW,接地!,26,Process Factor influence on WAT Para,Threshold Voltage(Vt=V,FB,+/-(2,F,+Q,BO,/C,OX,),Q,BO,=(2qN,B,(2,F,+V,SB,),1/2,(1)N,B,(Well and Sub Con.),Q,BO,V,t,(2)Gate Oxide,(a)Thickness:tox,C,OX,Vt,(b)Quality:Qfc,Vt(VFB=,ms-Qfc/COX),(3)Vt adjust(Vt imp,deep-imp.),(4)Poly1 CD,(Leff),Q,BO,V,t,(for short channel),(5)S/D implant,Vt,(For short channel),27,Process Factor influence on WAT Para,Gain factor:,=COX(W/L),Mobility,Id,a)G,OX,/,Si,interface quality,mobility,current Gain,b)Cannel implant Dose,mobility,current Gain,P1 CD,L,current Gain,G,OX,thickness,C,OX,current Gain,GAMMA FACTOR,N,B,C,OX,(G,OX,thickness,较厚,),=,(,2,qN,B,),1/2,/C,OX,=,Vt,/(2,f,+Vbs1)1/2-(2,f,+Vbs2),1/2,),28,Process Factor influence on WAT Para,Saturation Current:Id=1/2(,COXW/L)(Vgs-Vt)2,Vt,implant,Isat,G,OX,thickness,C,OX,Isat,Effective channel length,Leff,Isat,a)Poly1 CD(define,Leff,),Isat,b)S/D implant,c)Thermal Budget,Isat,(Lateral Diffusion),Weff,Isat,a)Nitride CD,Weff,Isat,b)Birds beak,encorach,Isat,29,Process Error Debugging,WAT Re-TEST and Bench,Meas,Searched on the,Promis,Track-in,track-out timing check.(Issue stage),Hold reason check.,Process flow check.,Equipment alarm check and Sorting.,In-line check.(View Chartand so on),STR lot,SEM and TEM check,30,Example introduce,Case1:P1/P2 Cap.Fail(lower),Case2:P+Rs Fail(higher),Case3:NMOS Idsat Fail(lower),Case4:PMOS Idsat Fail(lower),Case5:N/P MOS Isat all Fail(lower),31,谢谢观赏,
展开阅读全文